Water to grain ratio - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > All Grain & Partial Mash Brewing > Water to grain ratio

Reply
 
Thread Tools
Old 03-09-2010, 10:57 PM   #1
acleanthous
Recipes 
 
Oct 2009
Whatcom County, Washington
Posts: 9


I'm sure this has been discussed elsewhere in the forum and if so please direct me there. But I have a question about what to set my water to grain ratio for mashing at? I know there is science behind it and will affect the amount of fermentable sugars available, but I'm confused on picking a number.

I had one friend who has been brewing that told me setting it at 1.25 is to high, so I have been doing 1.1 for my last couple batches. Mash and sparge go smoothly but my efficiency is sticking around 58-60%. Alright I suppose. But, I feel like I should be getting more efficient mashes given my setup and our temperatures are holding fine.

Any opinions or recommendations? Thanks.

 
Reply With Quote
Old 03-09-2010, 11:05 PM   #2
HBHoss
Chappell Brewery
HBT_LIFETIMESUPPORTER.png
 
HBHoss's Avatar
Recipes 
 
Jul 2008
Mariposa, CA
Posts: 8,220
Liked 125 Times on 123 Posts


For mashing, 1.25 - 2 qts/lb of grain is the standard. Some people may go as thick as 1 qt/lb.

 
Reply With Quote
Old 03-09-2010, 11:39 PM   #3
malkore
 
malkore's Avatar
Recipes 
 
Jun 2007
Nebraska
Posts: 6,922
Liked 37 Times on 35 Posts


what he said. 1.25-2qt per pound is the normal range.

I find in my system that 1.3-1.4qt/lb for strike water is right. I batch sparge til I get the final pre-boil volume.
__________________
Malkore
Primary: English Mild
On tap: Pale Ale, Lancelot's Wheat, English Brown Ale, Steam Beer, HoovNuts IPA
Bottled: MOAM, Braggot, Raspberry Melomel, Merlot, Apfelwein, Pyment, Sweet mead, Cabernet
Gal in 2009: 27, Gal in 2010: 34, Gal in 2011: 13, Gal in 2012: 10

 
Reply With Quote
Old 03-10-2010, 05:44 AM   #4
acleanthous
Recipes 
 
Oct 2009
Whatcom County, Washington
Posts: 9

Okay, follow up question. Looking at blogs and others recipes in various steps throughout the mashing process the water to grain ratio raises. For example:

Temp Ratio Time
145F 1.0qt/lb 20min
158F 1.5qt/lb 20min
169F 1.9qt/lb 20min

So, at each of these steps am I adding cold water and then raising the mash temp to that step, or is there another method to the maddness?

Thanks again!!

- Alex

 
Reply With Quote
Old 03-10-2010, 05:59 AM   #5
bolts
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Sep 2009
Portland, OR
Posts: 306
Liked 8 Times on 7 Posts


I adjust my ratio to get even 1st/2nd runnings while batch sparging. This takes into account dead space in the mash tun and grain absorption. I've had anywhere from 1.2 to 2.2 ratios.

I base my madness on braukaiser's work here: http://braukaiser.com/wiki/index.php...rging_Analysis

 
Reply With Quote
Old 03-10-2010, 06:42 AM   #6
Palefire
 
Palefire's Avatar
Recipes 
 
Jun 2009
SF, CA
Posts: 1,124
Liked 12 Times on 9 Posts


There've been a lot of discussions about water/grain ratio here. 1.25 qt/lb used to be standard, but now lots of people use a higher ratio. I usually do 1.5 qt/lb, do a mash-out and a single sparge, and get a very consistent 74% efficiency. Lots of people mash higher (up to and even sometimes over 2 qts/lb) and find that doing so raises their efficiency with no detrimental effects to the final product. At very least, using more water makes it easier to stir and break up doughballs. I'd say try using more water and see what happens!


Quote:
Originally Posted by acleanthous View Post
Okay, follow up question. Looking at blogs and others recipes in various steps throughout the mashing process the water to grain ratio raises. For example:

Temp Ratio Time
145F 1.0qt/lb 20min
158F 1.5qt/lb 20min
169F 1.9qt/lb 20min

So, at each of these steps am I adding cold water and then raising the mash temp to that step, or is there another method to the maddness?
This sounds like a step-mash, which basically means adding hot water at each step to raise the temp of the mash. It's a more advanced technique, one that's not necessary for most beers (since the malting process today is more advanced than it used to be, or something like that - I'm sure there are lots of people on the forum who can explain it properly). IMO, not something to worry about until you get your system pretty well figured out.

 
Reply With Quote
Old 03-10-2010, 02:51 PM   #7
shortyjacobs
Recipes 
 
Aug 2009
Twin Cities, MN
Posts: 2,509
Liked 34 Times on 34 Posts


I do all mine with 1.5 qt/gal, single infusion, (no water addition to raise temps...just put it in at 1.5 qt/gal, drain 1st runnings, add sparge water, etc...)....I tried 1.2 qt/gal, and lost 10% efficiency.
__________________
Itchy Dog Brewery.

(As of 10-24-2011)
Primary - Steppe 112 PA, 2x Monday RyePA
Aging - None :-(
On tap - Big Dog, Apfelwein, Steppe 112 PA

My invisible AG sculpture, with no actual sculpture and a tiny footprint.
My Kegerator goes offroading!
My Coors Home Draft dispenser for boating/beering on the go.

 
Reply With Quote
Old 03-10-2010, 02:52 PM   #8
david_42
 
david_42's Avatar
Recipes 
 
Oct 2005
Oak Grove, Oregon, USA
Posts: 25,595
Liked 152 Times on 143 Posts


Step mashing isn't necessary for most beers, wheats are the exception. Use really hot water to raise the temperature, if you do.

Mash ratios between 5:1 and 7:1 by weight will give you better efficiency. In theory, a thick mash gives you a faster conversion, but with modern malts and a 60 minute mash, this really doesn't matter. Fermentability is also a consideration, but it is better controlled through mash temperatures.

Many homebrewers end up with thick mashes because they are pushing the limits of their equipment.
__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

 
Reply With Quote
Old 03-10-2010, 06:05 PM   #9
menschmaschine
 
menschmaschine's Avatar
Recipes 
 
Jun 2007
Delaware
Posts: 3,272
Liked 41 Times on 33 Posts


Quote:
Originally Posted by acleanthous View Post
I know there is science behind it and will affect the amount of fermentable sugars available, but I'm confused on picking a number.
Just a note on this. I had done variable mash thicknesses and never noticed a difference in wort fermentability. My suspicions were affirmed when Kaiser did some experiments on mash thickness and wort fermentability. The conclusion is that with modern malts, mash thickness doesn't seem to have much of an effect, if any, on wort fermentability.
__________________
END TRANSMISSION

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Grain to Water Ratio Graeme All Grain & Partial Mash Brewing 20 09-23-2009 09:17 AM
Water to Grain Ratio modenacart All Grain & Partial Mash Brewing 23 05-02-2008 02:11 AM
Good Grain Absorption Factor and Water/Grain Ratio? Mr. Mojo Rising All Grain & Partial Mash Brewing 8 03-13-2008 05:28 PM
Water to Grain Ratio LS_Grimmy All Grain & Partial Mash Brewing 4 04-07-2007 01:57 AM
Grain/Water Ratio? Evan! All Grain & Partial Mash Brewing 15 01-22-2007 07:00 PM


Forum Jump