ebay aquarium temp controller build - Page 269 - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Fermenters > ebay aquarium temp controller build

Reply
 
Thread Tools
Old 06-08-2012, 03:15 PM   #2681
lonepalm
HBT_LIFETIMESUPPORTER.png
Recipes 
 
Dec 2010
Raleigh, NC
Posts: 221
Liked 7 Times on 5 Posts


Quote:
Originally Posted by mirogster View Post
1. It may be only settings issue (looong delay time for saving fridge compressor).
2. Proper wiring issue (diy?)

Could you tell us what are you settings? (press and hold Set button)
PS. Is it scaled in F (not C) ???
I will once i get home this evening. I was really looking to getting a definition of what each setting was....

it is in F

I'll also take a pic of my wiring diagram



ROFL after looking through about 50 pages. I found the manual on page 249, going to confirm connections and set accordingly.

Reason: addition

 
Reply With Quote
Old 06-08-2012, 08:17 PM   #2682
JuanMoore
Recipes 
 
Oct 2009
The Old Pueblo
Posts: 21,885
Liked 3679 Times on 3501 Posts


Quote:
Originally Posted by lonepalm View Post
I will once i get home this evening. I was really looking to getting a definition of what each setting was....

it is in F

I'll also take a pic of my wiring diagram



ROFL after looking through about 50 pages. I found the manual on page 249, going to confirm connections and set accordingly.
With my posts per page settings there are only 34 pages in this thread for me, so I'm not sure which manual you're looking at. Most of this thread is in reference to the STC-1000, which has different wiring and different programming than the unit you have, so the manual you found may or may not be helpful. Just in case the manual you found isn't the correct one for your unit, here's a diagram and some programming instructions-



Press the SET key once to enter the control temperature setting, press ▲ or ▼ keys to adjust your set point temperature. Press SET button again to exit setting mode.

Press and hold SET button for three seconds to enter the system menu settings, press ▲ or▼ button to select the menu, press the SET button once to enter the appropriate parameter settings, press ▲ or ▼ button to modify the parameters.

After adjustment, you can exit by pressing the RST key, or by waiting for 5 seconds.

Menu codes:
HC Heating or Cooling mode control
d Temperature differential
LS Minimum set limits
HS Maximum set limits
CA Tempreature calibration
PT Compressor delay

The compressor delay comes factory set to 1 min, so if you weren't waiting 1 min for the relay to activate after turning the unit on, that very well could have been your problem. Once you get it up and running, I'd suggest putting the compressor delay at the max setting (10 min) to protect your compressor from short cycling.

Hope this helps.
__________________
I'm trying to find some porn filmed by a dog wearing a GoPro. - SharonaZamboni

Hunter, when you get bored, will you put a taco in my elephant's hands for me? - Hat

 
Reply With Quote
Old 06-08-2012, 08:26 PM   #2683
mirogster
Recipes 
 
May 2011
New York, New York
Posts: 125
Liked 8 Times on 6 Posts


+1 for 10 min compressor delay. Prolonged lifespan guaranteed.

 
Reply With Quote
Old 06-08-2012, 09:02 PM   #2684
carlisle_bob
Recipes 
 
Apr 2012
Carlisle, PA
Posts: 1,205
Liked 29 Times on 28 Posts


Quote:
Originally Posted by mirogster View Post
+1 for 10 min compressor delay. Prolonged lifespan guaranteed.
Hi

Very true except for *right now*. I just finished cleaning all my beer lines. When I do that I unplug the keezer. Just got it back on power and now I have to wait an extra 10 minutes to start cooling down..... I'm THIRSTY ....

Bob

 
Reply With Quote
Old 06-08-2012, 09:15 PM   #2685
mirogster
Recipes 
 
May 2011
New York, New York
Posts: 125
Liked 8 Times on 6 Posts


Patient my friend, be patient! By saying prolonged lifespan, I was also refering to your livers

 
Reply With Quote
Old 06-08-2012, 09:39 PM   #2686
carlisle_bob
Recipes 
 
Apr 2012
Carlisle, PA
Posts: 1,205
Liked 29 Times on 28 Posts


Quote:
Originally Posted by mirogster View Post
Patient my friend, be patient! By saying prolonged lifespan, I was also refering to your livers
Hi

But my liver's thirst too....

Also looks like the short cycle prevention is doing it's thing just fine. Held off for 10 minutes after power up. Then cooled down and cut out. Since the beast is warm inside, it went back up pretty fast. Short cycle cut in and it holding off re-starting the compressor.

Still thirsty ...

Bob

 
Reply With Quote
Old 06-09-2012, 12:10 AM   #2687
raouliii
HBT_SUPPORTER.png
 
raouliii's Avatar
Recipes 
 
Aug 2011
Ponchatoula, LA
Posts: 1,019
Liked 118 Times on 102 Posts


Quote:
Originally Posted by lonepalm View Post
Sorry to stretch this...i bought single stage controllers, but there are no instructions with it to set it and get it start the power to the outlet...

i can set a temp but can't seem to get it to fire up.

thanks
john
That looks like the new single stage I just substituted for my STC-1000. It was labeled as a CH54 on the box. Just didn't like that celcius.

I see an interesting difference between yours and the two I just purchased. The front bezels of mine have "Work" or "Cool" on the left and "Set" on the top along with a ones digit that is short like the decimal digit of the STC-1000. In fact upon inspection it appears to use the same LED module as the STC-1000. However, your front bezel indicates "Work" and "Set" both on the left and has a full size ones digit. I notice these kinds of things.

Here's an image of both pages of the instructions that came with mine. If you can't read it, I can send you a pdf if you message me with your email address.





 
Reply With Quote
Old 06-09-2012, 01:00 AM   #2688
carlisle_bob
Recipes 
 
Apr 2012
Carlisle, PA
Posts: 1,205
Liked 29 Times on 28 Posts


Hi

That's the WilHi something controller. Not as fancy as a STC-1000 and the relay is only rated to 5 amps. The STC-1000's are running about $17 delivered and the WilHi's are about $3 less.

Bob

 
Reply With Quote
Old 06-09-2012, 02:20 AM   #2689
raouliii
HBT_SUPPORTER.png
 
raouliii's Avatar
Recipes 
 
Aug 2011
Ponchatoula, LA
Posts: 1,019
Liked 118 Times on 102 Posts


Quote:
Originally Posted by carlisle_bob View Post
Hi

That's the WilHi something controller. Not as fancy as a STC-1000 and the relay is only rated to 5 amps. The STC-1000's are running about $17 delivered and the WilHi's are about $3 less.

Bob
The two I have are not labeled as Willhi's but they likely have a common source.


The relay is the exact same part as in my STC-1000 and is rated at 15A.

 
Reply With Quote
Old 06-09-2012, 01:46 PM   #2690
carlisle_bob
Recipes 
 
Apr 2012
Carlisle, PA
Posts: 1,205
Liked 29 Times on 28 Posts


Quote:
Originally Posted by raouliii View Post
The two I have are not labeled as Willhi's but they likely have a common source.


The relay is the exact same part as in my STC-1000 and is rated at 15A.
Hi

Yes indeed that is the exact same relay as the STC-1000. It's also the same PC board from what I can see in the picture.

Bob

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY temp controller build android DIY Projects 100 05-09-2013 01:14 PM
Control Fermentation temp with Aquarium Heater chemist308 General Techniques 20 12-15-2012 12:13 AM
question about "aquarium temperature controller" SamBrewer General Techniques 12 02-26-2011 07:30 PM
Attic Fan Temp Controller = Inexpensive Fermentation Controller???? Beernip General Techniques 5 06-16-2009 04:30 PM
Brutus Build Controller Box? gruversm Brew Stands 9 03-27-2009 03:54 AM


Forum Jump