Glycol vs Water for line cooling - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > Kegerators & Keezers > Glycol vs Water for line cooling

Reply
 
Thread Tools
Old 02-04-2010, 06:08 PM   #1
BSBrewer
Recipes 
 
Jan 2010
Bergen County, NJ
Posts: 390
Liked 3 Times on 3 Posts



Ok - so I am not one to cheap out or half ass anything but I don't really have the $$ in the budget right now to get a glycol pump for my system. I want to do a pond pump with a glycol pool but it appears as if a number of inexpensive pond pumps cant handle the glycol.

Other than having a lower freezing point what is the advantage of using glycol instead of just having water going through my trunk line to cool the beer. Does anyone just use water instead of glycol or can recommend a pond pump that can hold up in the glycol bath?



 
Reply With Quote
Old 02-04-2010, 06:27 PM   #2
jrfuda
Recipes 
 
Jun 2009
, NC
Posts: 136

I've been reading about glycol coolers too and have wondered about using a salt aolution instead. I pulled this from a wikipedia article:

At a concentration of 23.3%, the freezing point of NaCl brine is lowered to −21C (252.15 K, −6F)[

Seems like you'd get a pretty good safety zone, if you want to use this for lagering temps without having to worry about your lines freezing (compared to pure water). Seems like if aquarium equipment can withstand salt water, then it should be able to pull this off too. Of course, if you're using something like AC coils to cool the solution, it may not like the salt.

This is my completely unscientific opinion, though.


__________________
John
Primary: Air | Secondary: Air | T-A-D: Fu Below (2 Below Clone) | Bottled: American Amber Ale | Planned: SNPA Clone; SMaSHed Noble Blonde (Blonde brewed w/Pilsner and SAAZ)

 
Reply With Quote
Old 02-04-2010, 06:34 PM   #3
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,150
Liked 1622 Times on 1050 Posts


Well, if you're planning to put the cooling liquid reservoir in the same cabinet as your beer, you're obviously not going to worry about lowering the freezing point of the coolant. Water is fine.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 02-04-2010, 06:40 PM   #4
BSBrewer
Recipes 
 
Jan 2010
Bergen County, NJ
Posts: 390
Liked 3 Times on 3 Posts


Yes - doing a Keezer build (actually inspired by your youtube vid) and figured I'd put my pump and reserve in there.

Any chance you would know how to size a pump for my system? I am running approx 25' of trunk line with 5/16" poly for the coolant -

Opt 1 : will rise 23" - run horizontal 36" - drop 44" - run 16 ft - rise 48" - 5 x 90 deg bends

Opt 2 : rise 23" - run horizontal 16' - rise 16" - 3 x 90 deg bends

Don't have any clue as to what size pump I need - do I need like pond pump that does 210gph (7' lift max) or 325gph (12' lift max) - or is that going to have the stuff shooting out everywhere. Will an aquarium pump be enough?

Any guidance would be INCREDIBLY helpful!

On a side note I met two of the guys you may know from the Whales club - they were up at the Northern NJ brew club on Tuesday night - Gary and ??? (names aren't my forte) - they brought the group brew you guys aged in the apple jack barrel - kudos if you had any part of it.

 
Reply With Quote
Old 02-04-2010, 06:50 PM   #5
Mischief_Brewing
Recipes 
 
Jan 2010
Montpelier, VT
Posts: 1,261
Liked 16 Times on 14 Posts


I had a similar question earlier this year. The point somebody brought up that hit home with me was that having at least "some" alcohol in the system will keep mold and other unwanteds out. I don't want to have to clean it as often as the tap lines (even a closed system can get infected).

 
Reply With Quote
Old 02-04-2010, 07:18 PM   #6
goatchze
Recipes 
 
Nov 2008
College Station, TX
Posts: 108
Liked 1 Times on 1 Posts


While you could call glycol an alcohol (it's actually two attached to each other), I'm not sure about it's anti-microbial, biotic, whatever properties. You could just as easily use a Tbs or so of bleach in water to the same effect.

The only advantage of glycol cooling is that you can drop the glycol down below 32F without any worries. I'm not sure what the most popular glycol is for brewing, but a 50/50 mix of ethylene glycol and water has a freezing point of -45F or so. That's lower than any freezer goes. A 50/50 mix actually has a lower heat capacity than water (0.8 BTU/(lb*F) vs. 1.0 BTU/(lb*F) for water), which means that you'll need both more glycol as well as a high flowrate of glycol than water to give the same rate of cooling for your wort.

I've seen brine solutions mentioned here in the past, my problem with using a brine solution would be solids formation. You have to be pretty careful that you keep the concentrations correct. Too little salt and your water will freeze, too much salt and you run the risk of solids precipitating out of solution. With glycol, the margin is much greater (a 20% ethylene glycol solution freezes at around 10F, an 80% glycol solution freezes at around -45F)

The moral of the story is; if you don't intend to cool your "cold liquid" below freezing, there's not much point in using anything but water IMHO.

 
Reply With Quote
Old 02-04-2010, 08:55 PM   #7
bja
Recipes 
 
Nov 2007
Pittsburgh
Posts: 2,056
Liked 167 Times on 125 Posts


What about RV antifreeze? The kind they use in the sink drains and toilets. It's cheap and supposed to be non-toxic.

 
Reply With Quote
Old 02-04-2010, 08:58 PM   #8
Hang Glider
Beer Drinker
HBT_SUPPORTER.png
 
Hang Glider's Avatar
Recipes 
 
Mar 2007
North Augusta, SC
Posts: 3,204
Liked 194 Times on 147 Posts


RV antifreeze (pink) slushes at 0F, but my little Lowes pond pump has no problem living in a tank of it.

 
Reply With Quote
Old 02-11-2010, 03:38 PM   #9
BSBrewer
Recipes 
 
Jan 2010
Bergen County, NJ
Posts: 390
Liked 3 Times on 3 Posts


did a test run with a 425gph pond pump from lowes yesterday - comes through my 3/8" cooling line with no issues - test was with water but the final build I am going with the RV coolant
__________________
Bolero Snort Brewery...No BS - just ragin' good beers

On the journey from home brewing to brewery...follow our progress below:

BoleroSnort.com|Twitter|Facebook

 
Reply With Quote
Old 02-11-2010, 05:12 PM   #10
Synovia
Recipes 
 
Jan 2009
Chicago, Il
Posts: 1,330
Liked 6 Times on 6 Posts


Quote:
Originally Posted by BSBrewer View Post

Opt 1 : will rise 23" - run horizontal 36" - drop 44" - run 16 ft - rise 48" - 5 x 90 deg bends

Opt 2 : rise 23" - run horizontal 16' - rise 16" - 3 x 90 deg bends
.
Just a note here, but if the output of the lines is submerged, you have a closed loop system, and the height of rise is pretty much irrelevant (other than the initial filling of the system). Only the total length of tubing, diameter, and restrictive fittings matter.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
A new beer line cooling thread! SweetSounds Bottling/Kegging 19 02-22-2010 07:02 PM
Beer Line Cooling MikeZ Bottling/Kegging 4 01-22-2010 12:51 AM
DIY glycol cooling? Elfmaze Fermenters 24 01-22-2010 12:33 AM
Cooling line in the bottom of fridge? TJ-Bill Bottling/Kegging 2 01-26-2009 11:03 PM
Cooling down with water jaymack Beginners Beer Brewing Forum 14 01-12-2006 05:22 PM


Forum Jump