Gasketed Steel Enclosure for sale - Home Brew Forums
Home Brew Forums > Home Brew Market > For Sale > Gasketed Steel Enclosure for sale
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 01-08-2010, 12:43 PM   #1
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
iTrader: (0)
Liked 49 Times on 41 Posts



I have one extra control enclosure left over from my build.
Dimensions: 12.5" x 8.5" x 4" , has a 1.5" x 3.125" window in it. It has a panel inside to mount electronics on and a few electronic terminals, etc inside. There is a two digit digital screen of some kind still installed in the door. It appears to have read % of O2. Its NOT an LCD screen like that used in a Brewtroller. The door has a gasket and latch. Some switches and a buzzer are installed in the door. It will fit in the $14.50 Flat Rate Shipping box from USPS. I'm asking $35 plus shipping.





The panel in the background is not for sale. It's going to be my control panel housing the Brewtroller and other low voltage devices.



 
Reply With Quote
Old 02-14-2010, 01:13 PM   #2
capnr0n
Recipes 
 
Jan 2010
Belleville, IL
Posts: 12
iTrader: (0)

Is this enclosure still available?



 
Reply With Quote
Old 02-14-2010, 03:37 PM   #3
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
iTrader: (0)
Liked 49 Times on 41 Posts


Yep it is. If you want it I'll throw in some extra ribbon wires and thing left over from my build.

 
Reply With Quote
Old 02-14-2010, 03:52 PM   #4
capnr0n
Recipes 
 
Jan 2010
Belleville, IL
Posts: 12
iTrader: (0)

I'm thinking about it for a BrewTroller build, but I'm not sure that 12.5" x 8.5" is large enough to hold the BT3.1, BT 16 relay board, 12V PSU, SSR and 24VAC Transformer.

 
Reply With Quote
Old 02-14-2010, 04:19 PM   #5
capnr0n
Recipes 
 
Jan 2010
Belleville, IL
Posts: 12
iTrader: (0)

What are the dimensions of the internal sub-panel? If the sub-panel is 12.5 x 8.5, I think I can get everything to fit.

 
Reply With Quote
Old 02-14-2010, 04:46 PM   #6
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
iTrader: (0)
Liked 49 Times on 41 Posts


I'll measure it when I get home later but i have room for a dc power supply, BT, relay board. I have 5 SSRs so um putting them in a separate electrical junction box. I would say it's too small to put everything in one box. I'll send you a pic of what I have built so far.

 
Reply With Quote
Old 02-16-2010, 09:18 PM   #7
pickles
 
pickles's Avatar
Recipes 
 
Feb 2008
Columbus
Posts: 2,004
iTrader: (0)
Liked 49 Times on 41 Posts


!!!!!sold!!!!!



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Pump enclosure/control box nicadrick Equipment/Sanitation 11 12-21-2010 06:27 PM
Electrical Enclosure? JamieT Bottling/Kegging 2 08-05-2009 12:58 AM
Sanitary Gasketed Plate Heat Exchanger truckmann Equipment/Sanitation 3 08-02-2008 04:43 PM
Small serviceable (gasketed) plate chillers Bobby_M Equipment/Sanitation 4 12-20-2007 03:05 PM


Forum Jump