Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Need Help.....Question about quick disconnects
Reply
 
Thread Tools
Old 11-21-2009, 03:16 PM   #1
dood56
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: North Carolina
Posts: 36
Default Need Help.....Question about quick disconnects

I just brewed my first and am going to be building my keezer this weekend. However, I have run into an issue and I am not sure what to do. I put the gas and liquid disconnects on to my keg and on the proper peg. However, when I went to carb the beer, I didn't have anything on the output side and beer came shooting out of it. Pretty funny to the experienced I am sure. So I went to take off the liquid disconnect and it will not come off. I tried the same on the gas side and I can't get it off either. It was my understanding these were designed to be able to be pulled straight off. My keg is not pressurized either. I would really like an answer quickly since my beer is just sitting in the open now. I appreciate any assistance.


dood56 is offline
 
Reply With Quote
Old 11-21-2009, 05:09 PM   #2
boo boo
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2005
Location: Hearts's Delight, Newfoundland
Posts: 4,171
Liked 33 Times on 29 Posts
Likes Given: 4

Default

sounds like a poppit on the out side is stuck open. Try reseating it.
If the QDs are tight, make sure you have the correct QDs on the right posts.
Grey = gas and black = liquid.
If you had the liquid QD on the post when you pressurized and the QD wasn't attached to a tap then there is nothing to stop the beer.
To pull off the QD, lift the ring around the QD ( to release the stop ) and pull it up.


__________________
How do you BBQ an elephant....first you get your elephant....
boo boo is offline
 
Reply With Quote
Old 11-21-2009, 05:24 PM   #3
mitch171
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2009
Location: Finger Lakes, NY
Posts: 512
Liked 5 Times on 4 Posts

Default

Black Out...
mitch171 is offline
 
Reply With Quote
Old 11-21-2009, 06:38 PM   #4
dood56
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: North Carolina
Posts: 36
Default

Well, I went to my LBH and he was kind enough to point out I am an idiot. I do have black on the out side, but I put the in post on the out. So I essentially have placed the posts on the wrong sideas. Any recommendations on getting the disconnects off without damaging the posts would be appreciated.
dood56 is offline
 
Reply With Quote
Old 11-22-2009, 01:46 PM   #5
mitch171
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2009
Location: Finger Lakes, NY
Posts: 512
Liked 5 Times on 4 Posts

Default

I have done this, they will come off it just takes a lot of pulling. Make sure the locking ring is pulled up also.


mitch171 is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
NG quick disconnects?? sourmash Brew Stands 5 09-22-2009 12:40 AM
Quick Disconnects... Stile Equipment/Sanitation 8 01-13-2009 03:51 PM
Quick Disconnects Hodawg Bottling/Kegging 3 01-12-2009 12:30 AM
SS Quick Disconnects Ewalk02 Equipment/Sanitation 24 12-18-2008 12:25 PM
anyone tried these quick disconnects? vmpolesov General Techniques 5 03-27-2008 04:01 AM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS