Sanke Mash Tun Build - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > DIY Projects > Kettles, Mash Tuns & Hot Liquor Tanks > Sanke Mash Tun Build

Reply
 
Thread Tools
Old 10-06-2009, 04:01 PM   #1
Hoosier
Recipes 
 
Aug 2008
Porter, Indiana
Posts: 193
Liked 2 Times on 2 Posts



Hello Everyone,

I am planning on converting a sanke keg to a direct fire mash/lauter tun. I dug around the project locater but I was unable to find anything on this. I plan on picking up a ss flase bottom for it and the construction of the lauter system is easy. My question is what are you all using for insulation and lid during the mash. Please post any advice and pic's if available. Thanks in advance.

R,
Hoosier
__________________
Proud supporter of Brett, Lacto, Pedio and all the other critters your brewing friends warn you about.
www.thebrewingnetwork.com

 
Reply With Quote
Old 10-06-2009, 04:33 PM   #2
phillc
 
phillc's Avatar
Recipes 
 
Apr 2008
Posts: 143
Liked 1 Times on 1 Posts


No insulation, glass pot lid.

Mine is direct fired also. I heat half of the strike water in the HLT, and half in the MLT. This both warms up the entire MLT and cuts water heating time to less than half. I have found that using this process, there is no need for insulation. During last Saturday's brew I recirculated for a total of 4 minutes with very low heat to keep the temp at exactly 152.

Insulation is just one more cost and another thing to deal with when cleaning. Skip it!

 
Reply With Quote
Old 10-08-2009, 12:52 PM   #3
redneckbeagle
Recipes 
 
Oct 2007
Central KY
Posts: 161
Liked 1 Times on 1 Posts


Thinking of doing this also. I have lot's of questions.

Do you have to worry about scorching?

Or are you just adding enough heat to hold the mash temp?

Do you doing any stirring during the mash time, would that clog up the false bottom?
__________________
Cheers,

redneckbeagle

 
Reply With Quote
Old 10-08-2009, 01:06 PM   #4
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,201
Liked 1659 Times on 1072 Posts


I've avoided posting for a bit because I'm on the fence about sanke mash tuns. I know there are plenty of people here that have them and like them. Keep in mind, I currently brew on a direct fired sanke MLT so I'm not just speculating here.

If you want to direct fire it at any time during the mash, you really need a large false bottom in it so that the flame is heating liquid mash. In addition, you need a way to recirculate that now hot liquid back up onto the top of the grain bed to keep things from overheating. You have to be careful that you don't mill too finely or flow too quickly or you'll compact the grainbed and the false bottom will stop flowing. At that point, you'll have just a small amount of wort in the bottom, which will scorch, and your pump will lose prime. Oh, and there's no easy/cheap way of insulating while the flame is on. If you brew in ambient temps lower than 50F, trying to mash in an uninsulated tun is just wasteful.

Realizing some of these annoyances, one might suggest going to a RIMS (electric element tube exchanger) or HERMS system to avoid having to direct fire. I would agree that these options are probably a step in the right direction but once you stop direct firing, you might as well use a converted cooler as a mashtun because it's lighter, cheaper, easier to clean, and it's already insulated.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.


 
Reply With Quote
Old 10-08-2009, 06:13 PM   #5
phillc
 
phillc's Avatar
Recipes 
 
Apr 2008
Posts: 143
Liked 1 Times on 1 Posts


Bobby_M, correct as usual. I do have a large false bottom and I do recirculate. No scorching issues.

I prefer the Sanke MLT versus the cooler because:
1. Stainless. Cleans nicely, looks pretty, durable, welded fittings.
2. Direct firing allows me to maintain temperature completely independently of my HLT. This means that I can be preparing for a consecutive brew or preparing my sparge water without needing to worry about what the MLT is doing.
3. Size. Sure I could have used a large square cooler, but I like the round one, darn it! The biggest of those that I could find is 10 gallons which limited my OG capabilities.

I moved from a cooler to the sanke and haven't looked back.

Phill
.02

 
Reply With Quote
Old 10-12-2009, 03:32 PM   #6
ballegre
Recipes 
 
Nov 2008
Bahama, NC
Posts: 57
Liked 2 Times on 1 Posts


Quote:
Originally Posted by phillc View Post
Bobby_M, correct as usual. I do have a large false bottom and I do recirculate. No scorching issues.

I prefer the Sanke MLT versus the cooler because:
1. Stainless. Cleans nicely, looks pretty, durable, welded fittings.
2. Direct firing allows me to maintain temperature completely independently of my HLT. This means that I can be preparing for a consecutive brew or preparing my sparge water without needing to worry about what the MLT is doing.
3. Size. Sure I could have used a large square cooler, but I like the round one, darn it! The biggest of those that I could find is 10 gallons which limited my OG capabilities.

I moved from a cooler to the sanke and haven't looked back.

Phill
.02
So is the recommendation to use a false bottom, pick up tube and recirculation pump when using a keg for MLT? I too like the round one and want to do 10-12 gal batches.

I bought a bulkhead ball valve and braid from BargainFittings.com but I'm wondering what good is the braid. It doesn't create a siphon when draining and leaves a lot behind. Why do they even sell the braid? For coolers?

Thanks,

Bob

 
Reply With Quote
Old 10-12-2009, 04:12 PM   #7
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,201
Liked 1659 Times on 1072 Posts


If you want to direct fire, you really do want a large false bottom. If you don't direct fire, you can use the braid but you need to run a siphon tube down to the bottom and then attach the braid. However, you'd still need to insulate the heck out of the keg if you have no way of adding heat.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 10-12-2009, 06:39 PM   #8
FailureDrill
 
FailureDrill's Avatar
Recipes 
 
Jan 2009
Posts: 96
Liked 1 Times on 1 Posts


I have a setup with a braid at the bottom. I heat my water in the mash tun with the lid on which pre-heats everything. When the flame goes off, I wrap three layers of reflectix (from Lowe's) around the container. The reflectix is attached by velcro.



Here is my mashtun insulated lid. It's two aluminum pizza plates with styrofoam insulation inside and reflectix on the outside of the interior surface. Silver reflectix taps holds it all together.


This setup works well for me. Outside temps were about 55 in my garage yesterday while brewing. I mashed in a 158.5 and an hour later it was 157.2. I really think pre-heating the entire tun is the key.

medicbryan Likes This 
Reply With Quote
Old 10-12-2009, 06:53 PM   #9
ballegre
Recipes 
 
Nov 2008
Bahama, NC
Posts: 57
Liked 2 Times on 1 Posts


Thanks for the reply. I'm mostly interested in the braid, sparge and efficiency.

Do you have a single braid connected directly to bulkhead or connected to a pick up?

Do you find that there's a lot of wort left? Are your batches large enough so it doesn't matter?

Do you batch sparge?

Thanks,

Bob

 
Reply With Quote
Old 10-12-2009, 07:10 PM   #10
Lil' Sparky
Cowboys EAC
HBT_LIFETIMESUPPORTER.png
 
Lil' Sparky's Avatar
Recipes 
 
Feb 2006
Honolulu, HI
Posts: 3,959
Liked 72 Times on 46 Posts


I have a direct-fired sanke MLT. I have a sight glass installed so I can measure my strike water and heat it in the MLT. I really like being able to do this. When it's up to temp I can dough in and recirculate for a few mins. I don't use any insulation. If I did, I'd want it to be a high-temp, non-flammable type of insulation.

I have a full FB, and IMO it's the way to go with a sanke MLT. It keeps the grain bed elevated above the hot bottom when you're adding heat. I use a pump to recirculate when I'm adding heat (and sometimes during the entire mash just to keep the temps stabilized). If you let the grain rest on the bottom of the keg as you add heat, there's no way you can avoid hot spots in your mash, and if you're doing a 10 gal batch in there, stirring just isn't going to cut it, you have to recirculate. I do this to mashout and after each batch sparge addition, too and it performs a very nice vorlauf as a bonus.

Here's a pic of the inside of my MLT for your reference.



and a video of how I use it if you're interested.

__________________
Quote:
Originally Posted by duffman2 View Post
I dub this beer the Double Slutty Triple Nutty Bodacious Booty Brunette!

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Best way to insulate Sanke Mash Tun? Mr. Mojo Rising Equipment/Sanitation 10 01-26-2010 06:55 PM
Sanke mash-tun question Noleafclover Equipment/Sanitation 6 08-28-2009 02:34 PM
WTB Sanke keg for Mash-tun Midwest Noleafclover For Sale 2 08-15-2009 04:17 PM
Building a Sanke Mash Tun digdan Equipment/Sanitation 1 06-20-2006 09:06 PM
Sanke mash tun lid -- anyone ever tried this? Lounge Lizard Equipment/Sanitation 5 03-25-2006 04:59 PM


Forum Jump