Why can't I read a hydrometer correctly?? - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Beginners Beer Brewing Forum > Why can't I read a hydrometer correctly??

Reply
 
Thread Tools
Old 08-30-2009, 02:40 PM   #1
thejerk
Recipes 
 
May 2009
SLC!
Posts: 95
Liked 1 Times on 1 Posts



Things have been going very well for the last half a dozen brews or so. Consistent, decent efficiency, no major mistakes or screw-ups.
Then last night happened.
Get done with the entire sparge process and dipped into the kettle for a hydrometer reading. I fill the tube, set the hydrometer in it, and set it in the freezer for a couple of minutes while I set the kettle on the burner and get the flame going. Exact same thing I always do.
I go get the tube out of the freezer and check the hydrometer and the temperature. Spin it gently to make sure it's not sticking. Hydrometer reads 1.020 at 121 degrees. Plug it into promash, that means my preboil gravity is only 1.030?? Crap, that's 12 points low. I check my reading again. Yup. Hydrometer's not stuck, still reading the same. That puts me at about 50% efficiency?
So I'm pissed off, can't figure out what I did wrong in my mash, and add a pound of light DME to my boil and go on with the brewday.
Postboil gravity, taken from the end of the transfer to the carboy, and holy **** that hydrometer's floating high...1.076?? Now I've overshot my gravity 27 points??

I have no idea how I screwed this up. Obviously my preboil reading was off, but why? Good lord I'm retarded.

 
Reply With Quote
Old 08-30-2009, 02:43 PM   #2
Nurmey
I love making Beer
HBT_LIFETIMESUPPORTER.png
 
Nurmey's Avatar
Recipes 
 
Jul 2007
Omaha, NE
Posts: 3,983
Liked 30 Times on 26 Posts


Over 100 your hydrometer may not be reading correctly even with corrections for temperature. Try putting your pre-boil sample in a wide mouth shallow container to cool it down before adding it to the tube.
__________________
Batch 1 Brewing
The American Revolution would never have happened with gun control.

 
Reply With Quote
Old 08-30-2009, 02:46 PM   #3
Revvy
Post Hoc Ergo Propter Hoc
HBT_LIFETIMESUPPORTER.png
 
Revvy's Avatar
Recipes 
 
Dec 2007
"Detroitish" Michigan
Posts: 40,921
Liked 3184 Times on 1883 Posts


Quote:
Originally Posted by Nurmey View Post
Over 100 your hydrometer may not be reading correctly even with corrections for temperature. Try putting your pre-boil sample in a wide mouth shallow container to cool it down before adding it to the tube.
Or stick it in the fridge for awhile to cool down....

Or get a refractometer for the early gravities, you can get one drop cool enough to read almost instantly.
__________________
Like my snazzy new avatar? Get Sons of Zymurgy swag, here, and brew with the best.

Revvy's one of the cool reverends. He has a Harley and a t-shirt that says on the back "If you can read this, the bitch was Raptured. - Madman

I gotta tell ya, just between us girls, that Revvy is HOT. Very tall, gorgeous grey hair and a terrific smile. He's very good looking in person, with a charismatic personality... he drives like a ****ing maniac! - YooperBrew

 
Reply With Quote
Old 08-30-2009, 02:48 PM   #4
Nurmey
I love making Beer
HBT_LIFETIMESUPPORTER.png
 
Nurmey's Avatar
Recipes 
 
Jul 2007
Omaha, NE
Posts: 3,983
Liked 30 Times on 26 Posts


Oops! Yes, cool it in the fridge in the shallow container.
__________________
Batch 1 Brewing
The American Revolution would never have happened with gun control.

 
Reply With Quote
Old 08-30-2009, 02:48 PM   #5
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,201
Liked 1658 Times on 1071 Posts


My guess is that you didn't stir the wort and you were reading the lower gravity sparge that rested on top of the higher gravity first runnings. Stir the kettle well before taking a sample.
__________________
Welcome to BrewHardware.com. I love you.
BIAB Large Mesh False Bottoms and SS HERMS COILS are IN!!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Old 08-30-2009, 03:06 PM   #6
Edcculus
Recipes 
 
Jun 2007
Greenville, SC
Posts: 4,546
Liked 48 Times on 45 Posts


Quote:
Originally Posted by Nurmey View Post
Oops! Yes, cool it in the fridge in the shallow container.
make it a small stainless bowl. Metal conducts heat, while plastic and ceramic are insulators.

 
Reply With Quote


Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Beginner Video - How to read a Hydrometer Bobby_M Beginners Beer Brewing Forum 28 06-04-2009 03:05 PM
Broken hydrometer, read samples in a couple days? Jersh Beginners Beer Brewing Forum 2 03-01-2009 05:49 PM
Help me read my hydrometer, please. russb123 Beginners Beer Brewing Forum 5 09-09-2008 07:11 AM
accurate hydrometer read w/split pot boil? tranceamerica General Techniques 6 05-27-2008 04:39 PM
did I add my gelatin correctly? Walker General Techniques 2 09-12-2005 02:38 AM


Forum Jump