Foam problems on 1 of 2 taps? - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Foam problems on 1 of 2 taps?

Reply
 
Thread Tools
Old 08-24-2009, 06:35 AM   #1
jaobrien6
Recipes 
 
Jun 2007
Seattle, WA
Posts: 185
Liked 1 Times on 1 Posts



I'm curious if anyone has a suggestion for this one. I have a 2 tap kegerator. My beer lines are only 5', so I know I should go longer probably, but in the meantime, I'm a little confused by something. I have 2 beers on tap right now, both commercially filled corny's from the same brewery. One is dispensing very well, only a little extra foam in the first glass, but not bad at all. The other beer is dispensing with a *lot* of extra foam in the first glass. The keg's have been on tap for about a month now, so I'd think that even if they were carb'ed with different volumes of CO2 by the brewery, they'd have stabilized by now to my dispensing pressure of 10 psi. Any idea what else I should be looking at, for why one is coming out much much foamier than the other?

 
Reply With Quote
Old 08-24-2009, 07:50 AM   #2
jaja
Recipes 
 
Jan 2009
Posts: 153

Kinks in the hose? debri? Air in the lines? Beer kegged too early? A few things it could be.

 
Reply With Quote
Old 08-24-2009, 03:31 PM   #3
skibumdc
 
skibumdc's Avatar
Recipes 
 
Oct 2008
NoVa
Posts: 224
Liked 6 Times on 6 Posts


What kind of faucet?
Stainless Steel?

I know a BUNCH of people over on micromatic forum that had gunk build-up issues in the their faucets before they switched over to ALL SS faucets.

Disassemble your faucet completely and clean thoroughly, then reassemble.

What temp is the beer in the glass immediately after pouring.

 
Reply With Quote
Old 08-24-2009, 05:38 PM   #4
david_42
 
david_42's Avatar
Recipes 
 
Oct 2005
Oak Grove, Oregon, USA
Posts: 25,597
Liked 155 Times on 145 Posts


Swap the lines first to see if the problem is in the line or the beer.

But the real solution is to use longer lines.
__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

 
Reply With Quote
Old 08-24-2009, 09:16 PM   #5
jaobrien6
Recipes 
 
Jun 2007
Seattle, WA
Posts: 185
Liked 1 Times on 1 Posts


Quote:
Originally Posted by skibumdc View Post
What kind of faucet?
Stainless Steel?

I know a BUNCH of people over on micromatic forum that had gunk build-up issues in the their faucets before they switched over to ALL SS faucets.

Disassemble your faucet completely and clean thoroughly, then reassemble.

What temp is the beer in the glass immediately after pouring.
They are not stainless steel. I'm going to be upgrading to some perlicks shortly, so that should help out with that if it's part of the problem. I'll check the temp. I know I have a little bit of a warming problem in the tower. I'm not using any sort of blower at this time, but tried out the copper tubing passive cooling method. It has only worked so-so. However, I didn't figure warming was the problem since it should be affecting both beers equally.

 
Reply With Quote
Old 08-24-2009, 09:17 PM   #6
jaobrien6
Recipes 
 
Jun 2007
Seattle, WA
Posts: 185
Liked 1 Times on 1 Posts


Quote:
Originally Posted by david_42 View Post
Swap the lines first to see if the problem is in the line or the beer.

But the real solution is to use longer lines.
Good point, I should definitely swap the lines and see if it changes anything. I do plan on going to 10' lines, once these two kegs are kicked. I don't feel like swapping out the lines and fittings in mid-keg.

 
Reply With Quote
Old 10-05-2009, 10:38 PM   #7
jaobrien6
Recipes 
 
Jun 2007
Seattle, WA
Posts: 185
Liked 1 Times on 1 Posts


Quote:
Originally Posted by david_42 View Post
But the real solution is to use longer lines.
So I never did figure out exactly what was going on but I've got 10' lines now, as of last week, and so far everything is much, much better.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Regulator problems? Or Judo problems? Judochop Bottling/Kegging 11 05-13-2015 03:14 PM
Kegerator problems: foam Willsellout Bottling/Kegging 35 03-06-2014 06:14 PM
My first glass of beer from my kegged batch... all foam. The second? all foam. 3rd? nerdlogic Bottling/Kegging 24 11-15-2012 03:14 PM
Haier kegerator conversion - foam baby foam... lilzaphod Bottling/Kegging 5 10-08-2008 04:22 PM
Foam, foam, foam - any ideas? FlyGuy Bottling/Kegging 17 03-23-2007 01:50 AM


Forum Jump