Where in your keezer do you put your temperature controller probe? - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Where in your keezer do you put your temperature controller probe?

Reply
 
Thread Tools
Old 07-27-2009, 11:46 PM   #1
Stevorino
 
Stevorino's Avatar
Recipes 
 
Feb 2008
Alpharetta, GA
Posts: 938
Liked 2 Times on 2 Posts



My Chest freezer has a little 'step' where I've been sitting my temperature probe in a jar of water. After having problems with astringency in my beers recently, it finally hit me -- cold air sinks. I took a temp reading at my step (37 degrees) and then at the base of my chest freezer -- 26 degrees!!!

Beers I have been trying to hit at 2.5 volumes could be well over 3 volumes at that temperature.

So where do you put your keezer probe?
__________________
-Stevorino-_________________________________________
In Keezer:
1. BCS - Wet Hopped West Coast Blaster
2. CYBI - Gordon's IPA Clone
3. BCS - Scottish -80
4. BCS - Specialty Saison (Gold Medal at BMO)
In Process:
1. BCS - Janet's Brown Ale (Fermenting)

 
Reply With Quote
Old 07-27-2009, 11:53 PM   #2
HenryHill
HBT_LIFETIMESUPPORTER.png
 
HenryHill's Avatar
Recipes 
 
Mar 2007
Perry, MI
Posts: 3,040
Liked 11 Times on 11 Posts


I leave it in the bottom, or taped to the fermenter If I have something 'working'.
__________________
Quote:
Originally Posted by orfy
Never mock another man's brewery.
Quote:
Originally Posted by IrregularPulse View Post
This is HBT of course. Normal Thread that goes every direction but the one intended. This forum should be scientific proof the beer causes ADD

 
Reply With Quote
Old 07-28-2009, 12:14 AM   #3
Rick500
 
Rick500's Avatar
Recipes 
 
Jun 2008
KY
Posts: 2,612
Liked 15 Times on 13 Posts


You might consider rigging up a small DC fan to keep your temperature consistent in there.

 
Reply With Quote
Old 07-28-2009, 12:34 AM   #4
Stevorino
 
Stevorino's Avatar
Recipes 
 
Feb 2008
Alpharetta, GA
Posts: 938
Liked 2 Times on 2 Posts


Quote:
Originally Posted by Rick500 View Post
You might consider rigging up a small DC fan to keep your temperature consistent in there.
I was thinking the same thing-- I wonder if the moisture would present a problem...
__________________
-Stevorino-_________________________________________
In Keezer:
1. BCS - Wet Hopped West Coast Blaster
2. CYBI - Gordon's IPA Clone
3. BCS - Scottish -80
4. BCS - Specialty Saison (Gold Medal at BMO)
In Process:
1. BCS - Janet's Brown Ale (Fermenting)

 
Reply With Quote
Old 07-28-2009, 01:21 AM   #5
Rick500
 
Rick500's Avatar
Recipes 
 
Jun 2008
KY
Posts: 2,612
Liked 15 Times on 13 Posts


Yeah, you're right, probably a bucket o' Damp Rid too.

 
Reply With Quote
Old 07-28-2009, 01:32 AM   #6
Stevorino
 
Stevorino's Avatar
Recipes 
 
Feb 2008
Alpharetta, GA
Posts: 938
Liked 2 Times on 2 Posts


Quote:
Originally Posted by Rick500 View Post
Yeah, you're right, probably a bucket o' Damp Rid too.
There's no way I'm the only homebrewer to figure this out...maybe putting it on the bottom is the solution. My question is what temperature is the actual beer...
__________________
-Stevorino-_________________________________________
In Keezer:
1. BCS - Wet Hopped West Coast Blaster
2. CYBI - Gordon's IPA Clone
3. BCS - Scottish -80
4. BCS - Specialty Saison (Gold Medal at BMO)
In Process:
1. BCS - Janet's Brown Ale (Fermenting)

 
Reply With Quote
Old 07-28-2009, 01:44 AM   #7
Rick500
 
Rick500's Avatar
Recipes 
 
Jun 2008
KY
Posts: 2,612
Liked 15 Times on 13 Posts


I just listened to the July 13th Brew Strong podcast earlier today, and Jamil was saying if you don't want to use a Fermcap, the most accurate temperature measurement is going to be by taping the probe to the fermenter, at about the midpoint (vertically) of the column of beer. The podcast is well worth a listen.

 
Reply With Quote
Old 07-28-2009, 12:45 PM   #8
Benny Blanco
 
Benny Blanco's Avatar
Recipes 
 
Oct 2007
Rochester, NY
Posts: 327

I've never understood what's wrong with just pouring a nice tall glass and shoving the probe right in the beer. My keezer reads 47 but the temp of the actual beer is always around 3 degrees cooler.

 
Reply With Quote
Old 07-28-2009, 02:50 PM   #9
Stevorino
 
Stevorino's Avatar
Recipes 
 
Feb 2008
Alpharetta, GA
Posts: 938
Liked 2 Times on 2 Posts


Quote:
Originally Posted by Rick500 View Post
I just listened to the July 13th Brew Strong podcast earlier today, and Jamil was saying if you don't want to use a Fermcap, the most accurate temperature measurement is going to be by taping the probe to the fermenter, at about the midpoint (vertically) of the column of beer. The podcast is well worth a listen.
I may do this. I know that works for the glass of a carboy -- does it work for the stainless steel of a corny too?
__________________
-Stevorino-_________________________________________
In Keezer:
1. BCS - Wet Hopped West Coast Blaster
2. CYBI - Gordon's IPA Clone
3. BCS - Scottish -80
4. BCS - Specialty Saison (Gold Medal at BMO)
In Process:
1. BCS - Janet's Brown Ale (Fermenting)

 
Reply With Quote
Old 07-28-2009, 03:27 PM   #10
Arkador
 
Arkador's Avatar
Recipes 
 
Apr 2009
Fort Worth, TX
Posts: 1,702
Liked 16 Times on 15 Posts


my temp probe is in a 20oz bottle of water. I made a hole in the cap to feed the probe in, then hot glued it closed so i can't spill it.

the bottle sits on the floor of the keezer on the back wall next to 2 kegs. I keep it set at 40deg and my air temp thermometer is always between 36 and 42

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Which LOVE controller/probe? BeerElf Brew Stands 9 11-14-2012 01:54 AM
Keezer Temperature Controller Without Changing Freezer? Jif Bottling/Kegging 9 03-29-2012 03:34 PM
Other probe sensor for Love Controller? jordanpace Equipment/Sanitation 2 10-10-2008 09:10 PM


Forum Jump