Coldbreak Brewing Giveaway - Open to All!

Home Brew Forums > Home Brewing Beer > Bottling/Kegging > Dead end on CO2 leak
Reply
 
Thread Tools
Old 07-06-2009, 11:15 PM   #1
boredatwork
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2008
Location: Sunnyvale, CA
Posts: 281
Liked 7 Times on 7 Posts

Default Dead end on CO2 leak

I thought I had the problem solved, but then I went on vacation for 3 weeks and when I got back my CO2 tank was empty (again...).

My latest attempt at finding the leak was to stick the keg and co2 tank and regulator setup into a bathtub full of water. I spent a lot of time looking for bubbles in the water but I could not find any.

I filled the 5# CO2 tank two months ago, and since then it was used to fill maybe 24 bottles and dispense maybe 4 glasses of beer. For the rest of the time it was connected to 2 corny kegs in a fridge.

I am starting to wonder if CO2 tank will last either XX number of glasses dispensed, or 2 months of time, whichever comes first. I doubt this is normal for most people, but does anyone else have a problem with CO2 dissapearing after 2-3 months of not dispensing any beer?


boredatwork is offline
 
Reply With Quote
Old 07-06-2009, 11:17 PM   #2
Yooper
Ale's What Cures You!
HBT_ADMIN.png
Feedback Score: 0 reviews
 
Yooper's Avatar
Recipes 
 
Join Date: Jun 2006
Location: UP of Michigan
Posts: 65,125
Liked 5937 Times on 4232 Posts
Likes Given: 1515

Default

Quote:
Originally Posted by boredatwork View Post
I thought I had the problem solved, but then I went on vacation for 3 weeks and when I got back my CO2 tank was empty (again...).

My latest attempt at finding the leak was to stick the keg and co2 tank and regulator setup into a bathtub full of water. I spent a lot of time looking for bubbles in the water but I could not find any.

I filled the 5# CO2 tank two months ago, and since then it was used to fill maybe 24 bottles and dispense maybe 4 glasses of beer. For the rest of the time it was connected to 2 corny kegs in a fridge.

I am starting to wonder if CO2 tank will last either XX number of glasses dispensed, or 2 months of time, whichever comes first. I doubt this is normal for most people, but does anyone else have a problem with CO2 dissapearing after 2-3 months of not dispensing any beer?
I do- but I've found a few little leaks around the lid of one of my kegs, once the pressure got lower. It sealed fine when I gave it a shot of co2 at 30 psi, but afterwards it seemed like my co2 disappeared way too fast and I checked again and the lid had a very small leak around it. It drove me crazy!


__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

Follow me on facebook: https://www.facebook.com/lorena.t.evans
But I'm pretty boring so don't expect much!
https://www.facebook.com/lorena.t.evans
Yooper is offline
 
Reply With Quote
Old 07-07-2009, 01:40 PM   #3
david_42
Feedback Score: 0 reviews
 
david_42's Avatar
Recipes 
 
Join Date: Oct 2005
Location: Willamina & Oak Grove, Oregon, USA
Posts: 25,673
Liked 141 Times on 134 Posts

Default

Quote:
I am starting to wonder if CO2 tank will last either XX number of glasses dispensed, or 2 months of time, whichever comes first. I doubt this is normal for most people, but does anyone else have a problem with CO2 dissapearing after 2-3 months of not dispensing any beer?
I've got a small leak in my setup. I know what part of the system it is, between the regulator and the T-connector which splits the gas between the kegger and the conditioning cabinet, but like yours it's too small to find. I suspect one of the gauge bodies, but even immersing the whole rig doesn't show anything. So, I'm resigned to pressurizing the system and shutting the isolation valves. Fortunately, I can force carbonate using my other regulator and bottle.
__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk
david_42 is offline
 
Reply With Quote
Old 07-07-2009, 02:00 PM   #4
conpewter
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
conpewter's Avatar
Recipes 
 
Join Date: Nov 2007
Location: East Dundee, Illinois
Posts: 5,154
Liked 44 Times on 39 Posts
Likes Given: 13

Default

Quote:
Originally Posted by boredatwork View Post

I am starting to wonder if CO2 tank will last either XX number of glasses dispensed, or 2 months of time, whichever comes first. I doubt this is normal for most people, but does anyone else have a problem with CO2 dissapearing after 2-3 months of not dispensing any beer?
It won't empty by just sitting there. I have a tank from my grandpa that he's had for years (more than 10). It still has plenty of Co2 in it.

Normally when I hook up a corny I'll spray the lid/relief valve with star-san to check for leaks. I'll also stored my cleaned kegs with some star-san and a bit of pressure (2-3 lbs) and if they have pressure when I pull them out to fill them I know they'll be good. If not then I know I may need to mess with them a little to get a good seal. You may also want to spray star-san on all the connections between your tank and kegs. If that doesn't spot your leak you can get actual leak-testing stuff for gas lines, that should do it (I've never had to go buy that stuff though).
__________________
"People should not be afraid of their governments. Governments should be afraid of their people." - V

Primary: Nothin
Secondary: Shady Lord RIS, Water to Barleywine, Pumpkin wine, burnt mead
Kegged: Crappy infected mild
Bottles: Apfelwein, 999 Barleywine, Oatmeal Stout, Robust Porter, Robust smoked porter, Simcoe Smash
conpewter is offline
 
Reply With Quote
Old 07-07-2009, 03:00 PM   #5
hal2814
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2009
Location: Commerce, GA
Posts: 563
Liked 15 Times on 11 Posts

Default

Did you actually submerge your regulator?

To find leaks, I use dishsoap mixed with water and spray it on the connections. Same idea as the star-san idea above. And just to weed out the easy stuff, you do have that plastic washer between the tank and regulator, right?
hal2814 is offline
 
Reply With Quote
Old 07-07-2009, 03:24 PM   #6
Homercidal
Licensed Sensual Massage Therapist.
HBT_MODERATOR.png
Feedback Score: 0 reviews
 
Homercidal's Avatar
Recipes 
 
Join Date: Feb 2008
Location: Reed City, MI
Posts: 26,609
Liked 3342 Times on 2282 Posts
Likes Given: 2105

Default

Mine did the same thing this weekend. Happened once before. I've done the star san thing before and could not find any leaks. Frustrating...
__________________
If your takin' your girlfriend out tonight
You better park the car well out of sight
'Cos if they catch you in the back seat trying to pick her locks
They're gonna send you back to mother in a cardboard box !
Homercidal is offline
 
Reply With Quote
Old 07-07-2009, 03:48 PM   #7
Arkador
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2009
Location: Fort Worth, TX
Posts: 1,724
Liked 15 Times on 14 Posts
Likes Given: 10

Default

Quote:
Originally Posted by conpewter View Post
I'll also stored my cleaned kegs with some star-san and a bit of pressure (2-3 lbs) and if they have pressure when I pull them out to fill them I know they'll be good.
+1 on that!!!
Arkador is offline
 
Reply With Quote
Old 07-07-2009, 03:56 PM   #8
Trubadour
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2008
Location: Frisco, TX
Posts: 451
Default

Upon inspection, the black part on a few popets looked almost crushed on one side, so I replaced the popets and hope that fixes my leak that I can't find. Has anyone found that to be the source of their leaks?
__________________
...Cause it's the dank!

My Keezer
Trubadour is offline
 
Reply With Quote
Old 07-07-2009, 03:58 PM   #9
Arkador
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2009
Location: Fort Worth, TX
Posts: 1,724
Liked 15 Times on 14 Posts
Likes Given: 10

Default

a popet valve will only be a leak issue if the QD is disconnected. I have one keg that leaks from the gas in popet, but as long as I keep it hooked up, it is a nonissue. Same with having a beverage line connected to the liquid out.
Arkador is offline
 
Reply With Quote
Old 07-07-2009, 04:02 PM   #10
Trubadour
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2008
Location: Frisco, TX
Posts: 451
Default

Quote:
Originally Posted by Arkador View Post
a popet valve will only be a leak issue if the QD is disconnected. I have one keg that leaks from the gas in popet, but as long as I keep it hooked up, it is a nonissue. Same with having a beverage line connected to the liquid out.
I think that's my problem - I have 6 kegs in the keezer and only 4 taps and 4 gas connects, so they get disconnected and moved around occassionaly.

If you have the gas connected but manifold shut off, will it still prevent it from leaking there?


__________________
...Cause it's the dank!

My Keezer
Trubadour is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
dead yeast not dead -- how to cultivate and preserve? FSBrewer Beginners Beer Brewing Forum 6 10-19-2012 08:45 PM
C02 Leak eric_pwb Bottling/Kegging 10 11-07-2009 02:00 AM
co2 leak lowlife Bottling/Kegging 3 03-18-2009 04:12 PM
I've got a leak Professor Frink General Beer Discussion 11 05-31-2008 05:07 PM
Possible leak?? tim1970 Bottling/Kegging 8 04-17-2007 08:39 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS