dang i installed the wrong pid again!!! help - Page 4 - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > dang i installed the wrong pid again!!! help

Reply
 
Thread Tools
Old 07-12-2009, 05:27 AM   #31
keithster
Recipes 
 
Jul 2009
San Marcos, California
Posts: 42

Thanks for your reply.

Actuall I want to use one PID for the freezer. Have it turn on until it reaches the desired temp and then shut off until it starts to get warm again. You know, the same thing the built in temp controller does.

The second pid will be used to power a fan to circulate cold air for a small cold room. That fan will come on if the temp goes above 68 or whatever.

I just want a controller that I can run 120v to, wire the freezer or fan to, set the temp, and all is good.

 
Reply With Quote
Old 07-12-2009, 06:41 AM   #32
keithster
Recipes 
 
Jul 2009
San Marcos, California
Posts: 42

Sorry, getting late and made a duplicate post

Reason: duplicate post..... I'm a dope

 
Reply With Quote
Old 07-13-2009, 12:16 AM   #33
ClaudiusB
Recipes 
 
Dec 2007
El Paso, Texas
Posts: 1,363
Liked 104 Times on 81 Posts


keithster this is a good controller wit ON-OFF control mode Universal 1/16 DIN PID Temperature Controller [SYL-2362] - $41.95 : auberins.com, Temperature control solutions for home and industry

or the Love TS Dwyer Instruments - Series TS


Cheers,
ClaudiusB

 
Reply With Quote
Old 07-29-2009, 05:26 AM   #34
kickflip_mj
Recipes 
 
Jan 2008
Posts: 1,104
Liked 114 Times on 77 Posts


so sorry for the late response...


sawdust guy,

i was looking at your diagram and are you saying the prongs of the wall wort are conected to a seperate power source and the negative output of the wall wort is connected to #7 and the positive is connected to the SSR?

 
Reply With Quote
Old 07-29-2009, 08:50 AM   #35
Sawdustguy
 
Sawdustguy's Avatar
Recipes 
 
Mar 2009
Manorville, New York
Posts: 2,708
Liked 36 Times on 30 Posts


The wall wort can be connected to any 120 Volt AC source that is handy. Yes, connect the negative output of the wall wort to terminal #7 on the SYL-2342 and the positive output of the wall wort is connected to the (+) terminal of the SSR. Don't forget to connect a wire from terminal #8 on the SYL-2342 (-) terminal of the SSR.
__________________
Guy


 
Reply With Quote
Old 07-29-2009, 02:15 PM   #36
kickflip_mj
Recipes 
 
Jan 2008
Posts: 1,104
Liked 114 Times on 77 Posts


just the man i was looking for.

thank you for the response sawdustguy. i have finally got back to finishing my set up after working to much. just aquired a new danby fridge so the conversion begins. thank you for all your help so far.

 
Reply With Quote
Old 07-29-2009, 02:49 PM   #37
LooyvilleLarry
Recipes 
 
Aug 2008
Louisville,KY
Posts: 965
Liked 7 Times on 6 Posts


I would SOOOO give the guy at Aubern a ring a ling. He has always worked hard and fair for me and others here. I bet he can solve your problem.
__________________
Primary
Orange Cascade Pale Ale -

Secondary

Kegged
BeeCave Haus Ale - 6%
Bells Two Hearted, round 2- 6.1%
SNPA Clone (Chilled )
Hard Lemonade

Shiraz - 6 gal

 
Reply With Quote
Old 08-06-2009, 02:42 PM   #38
kickflip_mj
Recipes 
 
Jan 2008
Posts: 1,104
Liked 114 Times on 77 Posts


so i need help programming this dang thing.. the temp keeps raising 4 degrees above the set temp... could someone help me dial this thing in? i spent like 3 hours trying to figure it out

 
Reply With Quote
Old 08-06-2009, 08:29 PM   #39
kickflip_mj
Recipes 
 
Jan 2008
Posts: 1,104
Liked 114 Times on 77 Posts


any help would be appreciated

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Blow off tube installed... now what? underwaterdan General Beer Discussion 13 01-12-2009 06:23 PM
Dang it - Bad starter LooyvilleLarry Beginners Beer Brewing Forum 3 09-05-2008 03:50 PM
Dang my Ethics brandona33 Drunken Ramblings and Mindless Mumbling 35 03-05-2008 01:29 PM
New Faucets Installed! Tony Bottling/Kegging 1 01-14-2006 07:10 PM


Forum Jump