Mashing in a 50qt Cooler - Limitations? - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Mashing in a 50qt Cooler - Limitations?
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 06-28-2009, 12:46 PM   #1
briandickens
Recipes 
 
Aug 2007
Posts: 65


I have one of those igloo ice cube 50qt coolers that I have turned into a mash tun. I'm planning a big brew soon and I'm wondering what are the limitations on the mash tun so I don't run into issues.

My recipe for 10 gallons of blackIPA is calling for 31.5 lb of grain. According to rackers, at 1.25 qt/lb, that is going to take up 49.44qt in the cooler, leaving me with about half a gallon of space. Is that enough? Is the cooler truly 50qt inside? Or should I thicken the mash up to 1 qt/lb to be safe (that only takes up about 42 qt)? Maybe a volume somewhere between.

Note: I batch sparge so don't need room for a fly sparge arm or anything.



 
Reply With Quote
Old 06-28-2009, 01:04 PM   #2
Yooper
Ale's What Cures You!
HBT_ADMIN.png
 
Yooper's Avatar
Recipes 
 
Jun 2006
UP of Michigan, Winter Texan
Posts: 68,515
Liked 7369 Times on 5209 Posts


I found that when I followed the racker's calculator for my 10 gallon batch, I used 22 pounds of grain and 1.25 quarts per pound the calculator said it would take 8.64 gallons of space. Well, it was filled right to the top. Not an inch of space to spare in my 10 gallon Gott. The calculator can't take the space under the false bottom into account. If you have a manifold, your volume will be different than with a false bottom.

My MLT is different, of course, but I think that you will not be able to fit the 1.25 quarts/pound in your MLT if the calculator says you need 49.44 quarts of space.


__________________
Broken Leg Brewery
Giving beer a leg to stand on since 2006

 
Reply With Quote
Old 06-28-2009, 02:13 PM   #3
14thstreet
Recipes 
 
Apr 2009
Milwaukee, WI
Posts: 407
Liked 13 Times on 11 Posts


I remember reading elsewheres that 32 lbs is about the limit for that mash tun. I have the same but have never done anything that big. Start with 1 qt/lb, you can always add more later! Good luck and report back please!

 
Reply With Quote
Old 06-28-2009, 02:50 PM   #4
briandickens
Recipes 
 
Aug 2007
Posts: 65

Yeah. I think I'll start at 1qt/lb. If it gets stuck I can add water to it to loosen it up.

 
Reply With Quote
Old 06-29-2009, 03:27 AM   #5
wilserbrewer
BIAB Expert Tailor
HBT_SPONSOR.png
 
wilserbrewer's Avatar
Recipes 
 
May 2007
Jersey Shore, Jersey
Posts: 9,239
Liked 1255 Times on 959 Posts


Yea brian, if in doubt, i would mash thick and infuse hot (boiling) to get it running. Might take 3 batch sparges or so. Raise the grain bed temp near but not exceeding 170.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Video: How to make a mash tun from a 50qt Coleman cooler dustball All Grain & Partial Mash Brewing 8 05-19-2010 01:00 AM
rubbermaid 50qt cooler for mash tun minduim Beginners Beer Brewing Forum 4 03-01-2009 02:48 PM
5 gal igloo cooler for mashing. revrand65 Equipment/Sanitation 7 03-15-2007 05:51 PM
Cooler for mashing... Jer All Grain & Partial Mash Brewing 11 12-14-2006 01:03 PM
Mashing with a cooler sdent All Grain & Partial Mash Brewing 11 10-16-2005 01:18 AM


Forum Jump