Dialing in Temperature Control - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Dialing in Temperature Control
Cool Brewing Giveaway - Supporting Membership Drive & Discount

Reply
 
Thread Tools
Old 06-23-2009, 07:07 PM   #1
wendelgee2
Recipes 
 
Dec 2008
New York, NY
Posts: 324
Liked 3 Times on 2 Posts



Hey folks,
I use a Sanyo 4912 as a fermentation chamber. Just started with it.
I noticed the other day that even though the fridge is set to 70* the sticky thermometer on the carboy says 74*.

Do you usually drop the fridge temp a bit when the yeast is just getting started? Say, 66 to try to hit 70 in the carboy? Do you then raise it later?

Thanks.



 
Reply With Quote
Old 06-23-2009, 08:01 PM   #2
david_42
 
david_42's Avatar
Recipes 
 
Oct 2005
Willamina & Oak Grove, Oregon, USA
Posts: 25,576
Liked 148 Times on 139 Posts


I tape the temperature probe to the side of the fermenter and set the controller where I want it.


__________________
Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

 
Reply With Quote
Old 06-23-2009, 09:47 PM   #3
Dwain
Recipes 
 
Feb 2009
Hill Country, TX
Posts: 1,134
Liked 5 Times on 5 Posts


Quote:
Do you usually drop the fridge temp a bit when the yeast is just getting started? Say, 66 to try to hit 70 in the carboy? Do you then raise it later?

I tape the temperature probe to the side of the fermenter and set the controller where I want it.
From what I've read on here, either put you temp controller at 60*-62* or tape your temp probe to the fermenter. The fermentation process heats up the wort by about 10*. This is info I've gottoen from here, I'm not sure which one I'll do. Luck - Dwain

 
Reply With Quote
Old 06-24-2009, 03:59 AM   #4
passedpawn
Waste Allocation Load Lifter - Earth Class
HBT_ADMIN.png
 
passedpawn's Avatar
Recipes 
 
Apr 2009
☼ Clearwater, FL ☼
Posts: 25,041
Liked 6387 Times on 3785 Posts


He didn't say he had a temp controller. He might be just adjusting his fridge control. OG?

Yes, you want to try to keep the carboy at the yeast's optimal range. Since the fermentation creates heat (exothermic), the carboy will be many degrees warmer than it's surroundings. So, if you don't have a temp controller with a pendant sensor, you will want to just dial your fridge 5 degrees cooler than the desired temp until the bubbling subsides on the fermenter.

 
Reply With Quote
Old 06-26-2009, 03:58 AM   #5
wendelgee2
Recipes 
 
Dec 2008
New York, NY
Posts: 324
Liked 3 Times on 2 Posts


Quote:
Originally Posted by passedpawn View Post
He didn't say he had a temp controller. He might be just adjusting his fridge control. OG?
Sorry for being vague. Yes, I have a Johnson Controls analog temp controller.


Quote:
Originally Posted by passedpawn View Post
Yes, you want to try to keep the carboy at the yeast's optimal range. Since the fermentation creates heat (exothermic), the carboy will be many degrees warmer than it's surroundings. So, if you don't have a temp controller with a pendant sensor, you will want to just dial your fridge 5 degrees cooler than the desired temp until the bubbling subsides on the fermenter.
I knew it was exothermic, but not how exothermic. I'll dial down 5* next time and see what happens.

Also, anybody have thoughts on whether to set the fridge thermostat at max or min? Or is it immaterial, since the external temp controller controls the temp anyway? Does setting it to max give you faster recovery time, and thus less variation, or would a min setting give you more gradual temp curves, thus not upsetting the yeast as much?

Thanks folks. Ya'll rock. http://www.homebrewtalk.com/images/smilies/rockin.gif

 
Reply With Quote
Old 06-26-2009, 12:17 PM   #6
passedpawn
Waste Allocation Load Lifter - Earth Class
HBT_ADMIN.png
 
passedpawn's Avatar
Recipes 
 
Apr 2009
☼ Clearwater, FL ☼
Posts: 25,041
Liked 6387 Times on 3785 Posts


Set your fridge's temp controller to the coldest setting (max?)

 
Reply With Quote
Old 06-26-2009, 12:33 PM   #7
Boerderij_Kabouter
 
Boerderij_Kabouter's Avatar
Recipes 
 
Dec 2007
Oconomowoc, Wisconsin
Posts: 7,736
Liked 146 Times on 118 Posts


The heat generation depends on the vigor of the fermentation and the individual strain. I think about 7F is about average for a healthy ferment. The best thing to do is to have a thermowell or tape the probe to the fermenter with some insulation on the outside.

Also, IMO 70 is a hot fermentation, I would bet you will be happier fermenting around 65 (for most ales). Try it on your next beer and see. At 70, most ale yeasts will throw a lot of esters and phenols, it is cleaner at lower temps. Just another tool to be used. I ferment my raspberry weiss hot at around 72 to make a banana and bubblegum bomb that pairs well with the tart fruit.



 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Temperature Control jgbrown Beginners Beer Brewing Forum 3 09-30-2009 05:45 AM
DIY Temperature Control Reno_eNVy Fermenters 10 08-13-2009 07:13 PM
Temperature Control Arrogantbastard Equipment/Sanitation 7 01-16-2009 07:11 PM
Temperature Control Lochmiel2003 Beginners Beer Brewing Forum 7 11-12-2008 07:59 PM
Temperature Control bulleitb Beginners Beer Brewing Forum 6 04-26-2008 05:05 PM


Forum Jump