How Long Are Your QD/1/2" Silicon Hoses? - Home Brew Forums
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > How Long Are Your QD/1/2" Silicon Hoses?

Reply
 
Thread Tools
Old 05-03-2009, 02:00 PM   #1
HenryHill
HBT_LIFETIMESUPPORTER.png
 
HenryHill's Avatar
Recipes 
 
Mar 2007
Perry, MI
Posts: 3,040
Liked 11 Times on 11 Posts



I have 18' of silicon hose from B3 (only took 7 weeks). I have one pump now.

I had arbitrarily guessed 6' lengths, but am wondering, before I lay Craftsman Handicutters to it, how long everyone else went.

Reason being I plan on a dedicated single tier rig, but have been in traditional garage bench and floor configuration for awhile, and don't see a rig in the near future.

So what are your lengths, for either scenario?


__________________
Quote:
Originally Posted by orfy
Never mock another man's brewery.
Quote:
Originally Posted by IrregularPulse View Post
This is HBT of course. Normal Thread that goes every direction but the one intended. This forum should be scientific proof the beer causes ADD

 
Reply With Quote
Old 05-03-2009, 02:02 PM   #2
avaserfi
Recipes 
 
Nov 2008
College Station, TX
Posts: 630


I have 4-5ft runs for all my hose. My reasoning? None really - I figured it would be long enough without being too long.

I brew on the sidewalk in front of my apartment right now. Similar to the garage scenario, but less comfortable.


__________________
Andrew

 
Reply With Quote
Old 05-03-2009, 02:12 PM   #3
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


My advice would be to keep the hoses as short as possible, especially on the suction side of the pump. Short hoses = reduced resistance. My hoses were way longer than necessary when I first got my pump. Since then I've shortened them up with a significant improvement in pump performance. Priming seems to be easier too.

 
Reply With Quote
Old 05-04-2009, 01:24 PM   #4
HenryHill
HBT_LIFETIMESUPPORTER.png
 
HenryHill's Avatar
Recipes 
 
Mar 2007
Perry, MI
Posts: 3,040
Liked 11 Times on 11 Posts


Unfortunately I bought QD's before some posted here that they found that some QD 90's were helpful for hose use, but I had already bought straights.

Since I don't have a rig yet, I can't build the hoses specifically for them, not knowing the routings, so that my lengths are optimum. When I have the rig, I figure to just remove or cut the ends at the straights where I prefer 90's, but in the meantime I'm looking for brew rig owners that have gotten farther than myself in this.
__________________
Quote:
Originally Posted by orfy
Never mock another man's brewery.
Quote:
Originally Posted by IrregularPulse View Post
This is HBT of course. Normal Thread that goes every direction but the one intended. This forum should be scientific proof the beer causes ADD

 
Reply With Quote
Old 05-04-2009, 01:30 PM   #5
Catt22
Recipes 
 
Jan 2009
Posts: 4,998
Liked 69 Times on 62 Posts


Henry

Is that a Walther PPK maybe? Nice pistol. As Vince would say, "You know those Germans make good stuff"

 
Reply With Quote
Old 05-04-2009, 01:40 PM   #6
conpewter
HBT_SUPPORTER.png
 
conpewter's Avatar
Recipes 
 
Nov 2007
East Dundee, Illinois
Posts: 5,106
Liked 53 Times on 48 Posts


5ft on mine. Long enough for intlet or out let to reach any make disconnect, or the sink. Also I plumbed in a pipe over my brew-rig that runs through a good carbon filter and ends in a ball-valve with a male QD on it. I use it to fill the HLT and then anytime I need to rinse the pump (like after brewing) or if I loose my prime I can just attach the inlet QD to it and flush it out really well.
__________________
"People should not be afraid of their governments. Governments should be afraid of their people." - V

Primary: Nothin
Secondary: Shady Lord RIS, Water to Barleywine, Pumpkin wine, burnt mead
Kegged: Crappy infected mild
Bottles: Apfelwein, 999 Barleywine, Oatmeal Stout, Robust Porter, Robust smoked porter, Simcoe Smash

 
Reply With Quote
Old 05-04-2009, 01:48 PM   #7
phillc
Recipes 
 
Apr 2008
Posts: 143
Liked 1 Times on 1 Posts


Make them as long as they need to be... I think that your rig configuration will determine the proper lengths. Everybody's will be different.

 
Reply With Quote
Old 05-04-2009, 03:49 PM   #8
lehr
Recipes 
 
Dec 2008
flushing michigan
Posts: 786
Liked 17 Times on 17 Posts


Lay your stuff out on the floor in the way you intend to build your rig and use that as your guild line...The longest hose on mine is five foot and that is for the whirlpool recirculate on the chiller. You can see some of my hoses in this pic but not the long one that runs to the chiller...Hope this helps.
Pat
http://img256.imageshack.us/img256/232/img144121.jpg

 
Reply With Quote
Old 05-04-2009, 03:56 PM   #9
Bowtiebrewery
Recipes 
 
May 2009
Seymour, CT
Posts: 1,036
Liked 91 Times on 74 Posts


I just got into this game as well.. I only ordered 10ft from McMaster Carr.. but I'm confident that its more than enough... Hey Lehr... Not The Momma! from NB and More Beer forum here... Nice to see a familiar face... er.... Handle... lol

 
Reply With Quote
Old 05-04-2009, 04:02 PM   #10
TwoHeadsBrewing
Recipes 
 
Feb 2008
Chico, CA
Posts: 3,924
Liked 37 Times on 34 Posts


Keggle -> Pump Input: 4'
Pump Out -> Keggle: 6' (my MLT sits up fairly high, and I fly sparge)
MLT -> BK (gravity drain): 2'
CFC -> Carboy: 3'

Here it is in sparge mode:


__________________

Fermenting: ESB
Kegged: Extra IPA, Brown Ale, American Wheat, Blackheart Stout
Coming Up: Dunkleweizen, 3C Pale Ale


DIY Fermentation Chamber
More Brew Stuff

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What SIze Oetiker Clamp For 1/2" ID Silicon Hose On 1/2" Barbs HenryHill Equipment/Sanitation 5 11-03-2015 07:07 PM
10 ft hoses too long? macabra11 Bottling/Kegging 10 05-29-2009 07:16 PM
How long is "Smack Pack" yeast good for in the fridge and someothers BillTheSlink Beginners Beer Brewing Forum 8 04-14-2009 10:26 PM
For all the guys with long hoses EdWort Bottling/Kegging 34 11-12-2008 07:05 PM
Silicon Tubing for 3/8" brass barb noisy123 Brew Stands 1 07-22-2008 04:40 PM


Forum Jump