IPA water recipe - adjusting high bicarbonate water - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Brew Science > IPA water recipe - adjusting high bicarbonate water

Reply
 
Thread Tools
Old 03-10-2009, 04:40 PM   #1
conpewter
HBT_SUPPORTER.png
 
conpewter's Avatar
Recipes 
 
Nov 2007
East Dundee, Illinois
Posts: 5,107
Liked 53 Times on 48 Posts



I've gone around a bit with water chemistry on the forums before. I found some good spreadsheets (one done by BearCat which was really nice) but I think I'm going to settle into using Palmer's updated spreadsheet (It wasn't on his site when I read through the whole thing back on '07)

Here's the link

http://howtobrew.com/section3/Palmers_Mash_RA_ver2d.xls

This really is well made, and what I love about it is he tells us the password so we can change it to fit our needs (not that I've done that yet).

Anyway on to my question. I'm trying to replicate Burton on Trent's water. I have a high bicarbonate level (383 ppm...) which is close to their bicarbonates. To adjust my water to be similar I basically add a fair amount of Gypsum, which gets me close (though I have more Chloride than them 121 vs. 16). The thing I'm wondering is palmer's writing about sulfate and the stated values in Burton On Trent's water
Quote:
At concentrations over 400 ppm however, the resulting bitterness can become astringent and unpleasant, and at concentrations over 750 ppm, it can cause diarrhea. Sulfate is only weakly alkaline and does not contribute to the overall alkalinity of water.
How to Brew - By John Palmer - Reading a Water Report

My question here is that he reports Burton On Trent's water to be 820ppm, which would mean that everyone who drinks their water has diarrhea and the beer is astringent and unpleasant? I doubt this so I am wondering why 820ppm makes a very good IPA...
__________________
"People should not be afraid of their governments. Governments should be afraid of their people." - V

Primary: Nothin
Secondary: Shady Lord RIS, Water to Barleywine, Pumpkin wine, burnt mead
Kegged: Crappy infected mild
Bottles: Apfelwein, 999 Barleywine, Oatmeal Stout, Robust Porter, Robust smoked porter, Simcoe Smash

 
Reply With Quote
Old 03-10-2009, 10:27 PM   #2
BigEd
Recipes 
 
Nov 2004
Posts: 2,595
Liked 194 Times on 162 Posts


First I would not be too concerned with hitting exact numbers when shooting for a specific water profile. Frankly you will never be able to do it and as long as you are "in the ballpark" everything will be just fine. I have never seen any other comments on levels of sulphate @ 400ppm+. I can only give you my empirical data that in the many dozens of IPA I have brewed over the years with water adjusted to a Burton profile that problem has never been encountered by myself nor have I ever had a report of a problem from anybody drinking my beer.

 
Reply With Quote
Old 03-11-2009, 01:05 AM   #3
z987k
 
z987k's Avatar
Recipes 
 
Feb 2007
Anchorage
Posts: 3,518
Liked 29 Times on 27 Posts


Sulfate is the key to an IPA. It makes the hops shine through. With proper water adjustment you can get an IPA where you can pick out each hop as the beer moves across your palate. Go with the Burton upon Trent water profile.

 
Reply With Quote
Old 03-11-2009, 12:26 PM   #4
conpewter
HBT_SUPPORTER.png
 
conpewter's Avatar
Recipes 
 
Nov 2007
East Dundee, Illinois
Posts: 5,107
Liked 53 Times on 48 Posts


Thanks guys!

I always thought that I couldn't do light beers with my water (bicarbonates off the chart) but Burton upon Trent has the same bicarbs, just a crapload more calcium and sulfate. Luckly that is exactly the ions in Gypsum so I can adjust my water with that. I won't be able to get all the way up to their sulfate level, and I do have more chloride than their water, but I should be able to get close enough (as mentioned it is not anything you can get perfect).

Now for a pilsner I still need to buy distlled/RO water, but I can deal with that.
__________________
"People should not be afraid of their governments. Governments should be afraid of their people." - V

Primary: Nothin
Secondary: Shady Lord RIS, Water to Barleywine, Pumpkin wine, burnt mead
Kegged: Crappy infected mild
Bottles: Apfelwein, 999 Barleywine, Oatmeal Stout, Robust Porter, Robust smoked porter, Simcoe Smash

 
Reply With Quote
Old 03-13-2009, 02:54 PM   #5
wildwest450
Registered User
Recipes 
 
Dec 2007
Posts: 9,043
Liked 173 Times on 158 Posts


Good thread! I'm so frustrated with water reports, I wish i'd never had mine tested. To be honest I have no desire to delve into the science of water, it would be nice to have a base water reports one for low, medium and high srm beers. I read somewhere that even though the Burton upon Trent is good for Ipa's it was overly high on some of the levels.

That's why a base level for certain styles would be a great thing! Hint, hint.
Slowly backs away from the water nerd's and runs away.

 
Reply With Quote
Old 03-13-2009, 04:32 PM   #6
SpanishCastleAle
 
SpanishCastleAle's Avatar
Recipes 
 
Jan 2009
Central Florida
Posts: 4,345
Liked 36 Times on 36 Posts


Quote:
Sulfate is the key to an IPA.
Sulphate alone or the Sulphate:Chloride ratio? Palmer talks about how the ratio affects the crispness/maltiness respectively and his spreadsheet shows high Sulphate:Chloride ratio as 'Bitter to Very Bitter' and low ratio as 'Malty and Very Malty'.

But I've never done any tests or anything...just sort of taken it as gospel and went with it. Truly asking here.

I've always been a leetle skeered to try BOT water or Dublin water profiles...so extreme. Then again I'll make an uber-soft Pils water and think nothing of it...obv I'm biased.
__________________
Early brewers were primarily women, mostly because it was deemed a woman's job. Mesopotamian men, of some 3,800 years ago, were obviously complete assclowns and had yet to realize the pleasure of brewing beer.- Beer Advocate

 
Reply With Quote
Old 03-13-2009, 07:48 PM   #7
z987k
 
z987k's Avatar
Recipes 
 
Feb 2007
Anchorage
Posts: 3,518
Liked 29 Times on 27 Posts


Quote:
Originally Posted by SpanishCastleAle View Post
Sulphate alone or the Sulphate:Chloride ratio? Palmer talks about how the ratio affects the crispness/maltiness respectively and his spreadsheet shows high Sulphate:Chloride ratio as 'Bitter to Very Bitter' and low ratio as 'Malty and Very Malty'.

But I've never done any tests or anything...just sort of taken it as gospel and went with it. Truly asking here.

I've always been a leetle skeered to try BOT water or Dublin water profiles...so extreme. Then again I'll make an uber-soft Pils water and think nothing of it...obv I'm biased.
Your right, it's not sulfate alone, it has to do with the chlorine to, and every other ion kind of. But in everything I've read and experienced sulfate is very key to getting that multi-dimensional IPA.

When I get home I'll look some stuff up in Brew Science if you want... or you could download it.

 
Reply With Quote
Old 05-24-2009, 08:04 AM   #8
TheChemist
Recipes 
 
Oct 2008
Cowtown, Alberta
Posts: 65
Liked 6 Times on 1 Posts


The reason Burton on Trent made light beer is because they couldn't do anything else well - they were limited by their water! The 800+ppm thing is similar to the numbers I have, but that's well above what you'd need. Think 'saturation' levels - you'd only need half that in order to accomplish what you want.

Sulphate increases detectable bitterness, so it your beer has a greater, fuller bitter taste to it. Without a balance of chloride though, it becomes icky and almost 'coats' your tongue - there IS such a thing as too much.

For style-appropriate levels, I posted some general guidelines in my 'pH and water treatment' thread - it's not very pretty right now, but I'll see if I can find something easier to read.

 
Reply With Quote
Old 10-28-2009, 04:55 AM   #9
mramann
Recipes 
 
Nov 2008
Posts: 38
Liked 1 Times on 1 Posts


Another note when trying to adjust your water to a classic profile: we don't necessarily have any idea what those breweries are doing to their water once they pull it from the municipal system. From this information we may be able to understand why certain styles are indigenous to certain areas, and what the overall function of certain minerals is and their ratio to each other. But we can't duplicate a profile and expect our beer to mirror that of the classic city.

Palmer does nail it pretty well in his book. But there is a lot of room to tinker with each specific water profile. You and I could brew the exact same beer and end up with a noticeably different result. It's the final frontier of brewing...?

 
Reply With Quote
Old 08-17-2010, 04:19 PM   #10
mb2696
HBT_SUPPORTER.png
Recipes 
 
Oct 2009
charlottesville, va
Posts: 427
Liked 6 Times on 6 Posts


conpewter, did you ever do this? how did it turn out? i'm looking to do a burton profile but it just seems like so much...

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
effectiveness of pre boiling water to remove bicarbonate MattHollingsworth General Techniques 14 10-11-2010 11:08 AM
Adjusting Water murphyslaw All Grain & Partial Mash Brewing 2 09-01-2009 09:46 PM
Bicarbonate in water once again, Green Flash IPA MattHollingsworth Brew Science 13 06-17-2009 05:50 AM
My Water: Too much bicarbonate & sodium brundage Brew Science 6 05-19-2009 03:56 PM
adjusting water caver95 All Grain & Partial Mash Brewing 6 03-25-2009 03:54 PM


Forum Jump