Coldbreak Brewing HERMS Giveaway!

HomeBrewSupply AMCYL Brew Kettle Giveaway!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > kegerator shank drill bit size craziness
Reply
 
Thread Tools
Old 02-26-2009, 05:39 PM   #1
docmoran
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2008
Posts: 132
Default kegerator shank drill bit size craziness

Can anyone tell me what size drill bit or hole to drill into my fridge to accomodate a shank. The widest diameter I can measure is 3/4 inch and the people at the HBS are telling me 1 inch. I feel so stupid but isnt that gonna let air out?? Whats up with the "sleeves" I have heard people talk about? Just trying to not ruin fridge and get some beer kegged/cooled/and drinked!!! thanks


docmoran is offline
 
Reply With Quote
Old 02-26-2009, 05:49 PM   #2
GilaMinumBeer
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
GilaMinumBeer's Avatar
Recipes 
 
Join Date: Jan 2008
Posts: 52,274
Liked 5870 Times on 5104 Posts
Likes Given: 80

Default

I drilled 1".

At first I left the cavity around the shank. The trim cover on the service side and the washer/nut on the inside will stop any air movement. But, the faucets will get cold (mine did at least).

Later I decided to pack some foam window seal inside the cavity. I think it just caused the shank to stay warmer so I pulled it back out.

No air moves but, somehow the lack of filler allows the faucets and shanks to chill and I think this is better.


GilaMinumBeer is online now
 
Reply With Quote
Old 02-26-2009, 07:18 PM   #3
docmoran
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2008
Posts: 132
Default

Excellent, and makes sense -- I do see how the trim cover and nut keeps it stationary and the getting cold thing makes sense -- Im going with the 1 inch bit! thanks, doc
docmoran is offline
 
Reply With Quote
Old 02-26-2009, 07:37 PM   #4
IrregularPulse
Hobby Collector
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
IrregularPulse's Avatar
Recipes 
 
Join Date: Nov 2007
Posts: 46,308
Liked 3001 Times on 2908 Posts
Likes Given: 148

Default

I second the 1 incher. I then have a 1.5" layer of rigid foam against the inside front panel of my tap box that the shanks also go through before breaking into the open inside of the tap box.
__________________
Tap Room Hobo

I should have stuck to four fingers in Vegas. :o - marubozo's mom
IrregularPulse is online now
 
Reply With Quote
Old 02-26-2009, 07:41 PM   #5
wildwest450
Registered User
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2007
Posts: 9,099
Liked 170 Times on 155 Posts
Likes Given: 4

Default

Quote:
Originally Posted by IrregularPulse View Post
I second the 1 incher.
That aint what she said.

It's good if your tap stay's cold, less foaming is more better.
wildwest450 is offline
 
Reply With Quote
Old 02-27-2009, 04:17 AM   #6
boogyman
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2009
Location: Folsom, CA
Posts: 417
Liked 2 Times on 2 Posts

Default

I used a 1" hole saw bit as well. I lined the hole with metal duct tape as well to prevent foam from crumbling all over the place... no other sealant. Taps are nice and cold too.
boogyman is offline
 
Reply With Quote
Old 02-27-2009, 12:42 PM   #7
SpanishCastleAle
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2009
Location: Central Florida
Posts: 4,384
Liked 35 Times on 35 Posts

Default

Quote:
Later I decided to pack some foam window seal inside the cavity. I think it just caused the shank to stay warmer so I pulled it back out.

No air moves but, somehow the lack of filler allows the faucets and shanks to chill and I think this is better.
Seems to me there is a cold side (inside the fridge) and a warm side (outside the fridge) to the entire faucet/shank assembly. So if you insulate the inside/cold side from the cold then the warm side wins and the assembly stays relatively warm. But if you were to insulate the outside/warm side from the warm then the cold side wins and it would get even colder. So if you want the faucet even colder...insulate the outside.
__________________
Early brewers were primarily women, mostly because it was deemed a woman's job. Mesopotamian men, of some 3,800 years ago, were obviously complete assclowns and had yet to realize the pleasure of brewing beer.- Beer Advocate
SpanishCastleAle is offline
 
Reply With Quote
Old 02-27-2009, 01:20 PM   #8
IrregularPulse
Hobby Collector
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
IrregularPulse's Avatar
Recipes 
 
Join Date: Nov 2007
Posts: 46,308
Liked 3001 Times on 2908 Posts
Likes Given: 148

Default

I poured my first fully carbed beer from the tap last night with the full tap setup. Poured right down the middle, Nice steady pour leaving a 3/4" head. Good stuff.
__________________
Tap Room Hobo

I should have stuck to four fingers in Vegas. :o - marubozo's mom
IrregularPulse is online now
 
Reply With Quote
Old 02-27-2009, 01:59 PM   #9
SOB
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2006
Location: Delaware, OH
Posts: 975
Liked 6 Times on 6 Posts

Default

For some reason I want to say I drilled a 7/8" hole and the shaft fit in nice and tight (giggity). No room around the shaft to even put any foam.

EDIT: Hmm...it seems like every site I looked at (Austin and Midwest) say a 1" hole. Maybe I'm retarded or something!
__________________
"So we were slammin' beers in the church parking lot..."

"I'm much too young to feel this damn old"

SOB is offline
 
Reply With Quote
Old 02-27-2009, 04:46 PM   #10
Coy-Boy
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2009
Location: Northern VA
Posts: 36
Default

I used a unibit meant for electrical knockouts. Bought it at Home Depot. It has a "step" for 7/8" and it fit perfectly.


Coy-Boy is offline
 
Reply With Quote
Reply


Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What size Shank do I need? Stevorino Bottling/Kegging 7 05-13-2012 10:42 PM
How to know what size and diameter of shank assembly? GroosBrewz Bottling/Kegging 1 06-22-2009 05:13 AM
What size holes to drill? IBUPIMP Kettles, Mash Tuns, & Hot Liquor Tanks 2 04-25-2009 04:08 PM
What size shank? underwaterdan Bottling/Kegging 2 01-03-2009 02:42 AM
Shank bore size Q for kegerator? EamusCatuli Equipment/Sanitation 1 08-01-2008 02:29 PM


Forum Jump

Newest Threads

LATEST SPONSOR DEALS