Keggle - How high to drill the hole for the valve? - Home Brew Forums
Register Now For Free!

Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Keggle - How high to drill the hole for the valve?

Reply
 
Thread Tools
Old 02-24-2009, 09:34 PM   #1
atkinsr
Recipes 
 
Feb 2009
Charlotte, NC
Posts: 23


Top cut, keg semi-polished. weldless fitting, ball-valve, etc. in hand. I don't have the pick-up tube or any false bottom yet. I'm setting these up so as to be completely interchangeable.

Can somebody tell me how high above the skirt weld I should drill the hole for the valve/shank assembly? since I don't have the pick-up tube in hand, I don't know if it should be 1/2", 1/2', or 1/2 mile (though I'm guessing that last answer is wrong!).

Thanks!

 
Reply With Quote
Old 02-24-2009, 09:55 PM   #2
culaslucas
 
culaslucas's Avatar
Recipes 
 
Aug 2008
Boulder, CO
Posts: 397
Liked 6 Times on 6 Posts


it can really be as high as you want as long as the siphon tube reaches the bottom and the tube on the outside of the keggle is lower than the bottom of that siphon tube. Although you'll have a really tough time siphoning if it's at the top of the keg. Mine is a couple inches off the bottom...lower is better...

__________________
Quote:
Originally Posted by chefmike
FEAR THE APFEL FOAM!!!!!!


 
Reply With Quote
Old 02-24-2009, 10:02 PM   #3
atkinsr
Recipes 
 
Feb 2009
Charlotte, NC
Posts: 23

Thanks for the reply. When you talk about the tube on the outside being lower than the bottom of the pick-up tube, you are talking about the drain tube, not the ball valve outlet, correct? I can't imagine how the valve outlet itself would be lower than the pickup tube.

Thanks again!

 
Reply With Quote
Old 02-24-2009, 10:13 PM   #4
culaslucas
 
culaslucas's Avatar
Recipes 
 
Aug 2008
Boulder, CO
Posts: 397
Liked 6 Times on 6 Posts


correct - I was referring to the exterior drain tube.
__________________
Quote:
Originally Posted by chefmike
FEAR THE APFEL FOAM!!!!!!

 
Reply With Quote
Old 02-24-2009, 11:09 PM   #5
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
 
Bobby_M's Avatar
Recipes 
 
Aug 2006
Whitehouse Station, NJ
Posts: 23,333
Liked 1765 Times on 1122 Posts


It should be as low as possible but not so low that your seal is going to hit the curve.
__________________
Welcome to BrewHardware.com. I love you.
New Stirplates are IN!
Chugger Pumps, Pump Kits, Camlocks, Sightglasses, Clear USA made Silicone Tubing, RIMS, Electric Install Parts, etc.

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
who could drill my kettle hole doubleb Equipment/Sanitation 35 07-20-2010 12:18 PM
Did you drill a hole in the bottom of your keg? TerapinChef Equipment/Sanitation 16 02-18-2009 01:53 AM
Hole Saw Set...OK for keggle drill? broadbill Equipment/Sanitation 32 11-22-2008 01:38 AM
where to drill the hole bru-er Equipment/Sanitation 2 04-17-2008 12:47 AM
How high to drill the 7/8th hole? Ol' Grog Equipment/Sanitation 5 03-30-2007 06:00 PM


Forum Jump