stir plate help - Home Brew Forums
Home Brew Forums > Home Brewing Beer > DIY Projects > Chillers & Stir Plates > stir plate help

Reply
 
Thread Tools
Old 02-20-2009, 04:49 AM   #1
ak47clown
Recipes 
 
Dec 2008
dirty jersey
Posts: 86


Ok-so I've read just about every thread out there and tried all the recommendations with no avail. I've built myself a stir plate and at best i can get a 1-2" funnel to appear in my 1 liter flask but for the most part, i keep throwing the magnet(s). I have a 1 5/8" stirbar

Here is what i've tried so far:

-1 hard drive magnet
-2 hard drive magnets
-2 1/4" round neodymium magnets
-2 1/2" donut shaped neodymium magnets
-3 different fans (120mm, 60mm, and a low speed 1000rpm that i just purchased today)
-I've varied the distance from the flask to the magnets
-I've put the flask on the plate without the fan on and then flipped it on.
-I've tried just about every magnet location/position/polarity combination i can think of.

My best configuration yet was the 120mm fan (not sure of rpm but slightly higher than my 1k rpm fan) with two hard drive magnets but the problem was, my magnets were killing the fan and it was straining to spin even at full voltage so it would never spin fast enough. If i rotated the magnets 90 degrees, the fan spun much easier but i did not have the same success with my stirbar...

Am i just completely missing something? I can't believe it can be this freaking hard...


__________________
:::_____________:::

Primary: Bass Ackwards Brew
Secondary:
Bottled: Magic Hat #9 clone, Amarillo IPA, Lemon Coriander Weiss
Up next: ?

 
Reply With Quote
Old 02-20-2009, 04:59 AM   #2
Cookiebaggs
Recipes 
 
Mar 2007
Oak Creek, WI
Posts: 538
Liked 6 Times on 3 Posts


What is your power voltage? I use an adustable power supply that allows me to change the voltage. This helps to dial in the stirplate to a range where the rheostat can go faster and slower within that voltage setting. Also, how much space is there between the magnet on the fan and the surface of the project box? It should be as close as possible.

I used one magnet and it works awesome.







 
Reply With Quote
Old 02-20-2009, 06:26 PM   #3
ak47clown
Recipes 
 
Dec 2008
dirty jersey
Posts: 86

I've got an adjustable regulator with a pot that I've got with a range from 4.5v-12v. I do not have anything mounted in my enclosure so i've played with a range a distances from the plate by just stacking cd cases...
__________________
:::_____________:::

Primary: Bass Ackwards Brew
Secondary:
Bottled: Magic Hat #9 clone, Amarillo IPA, Lemon Coriander Weiss
Up next: ?

 
Reply With Quote
Old 02-20-2009, 06:37 PM   #4
XXguy
Recipes 
 
Dec 2008
Southeastern PA
Posts: 1,118
Liked 16 Times on 15 Posts


try a smaller stirbar? I've had good success using some "X" shaped stirbars I got off Ebay that seem to be more tolerant of different speeds without getting thrown off. I also use just a single magnet, but for me, it seems the closer I got the magnet to the lid, the better my setup worked.

 
Reply With Quote
Old 02-20-2009, 06:45 PM   #5
Homercidal
Licensed Sensual Massage Therapist.
HBT_MODERATOR.png
 
Homercidal's Avatar
Recipes 
 
Feb 2008
Reed City, MI
Posts: 30,320
Liked 4665 Times on 3142 Posts


I don't know. Mine is ok and it's nothing special. Standard fan and a pair of mags. I have a pot that adjusts, but I don't need to use it. I think I'm running that 12V fan at like 6 or 9 volts off a universal wall plug.

You know you don't actually need a vortex to get a good stirbar. It's cool looking, but just swirling the stuff around is keeping it mixed.

 
Reply With Quote
Old 02-20-2009, 06:52 PM   #6
BadCatBrewer
Bad Cat Brewer
HBT_LIFETIMESUPPORTER.png
 
BadCatBrewer's Avatar
Recipes 
 
Dec 2008
Atlanta, GA
Posts: 43

All fans are not created equally. On my first attempt, I used an old 80mm computer fan and one hard drive magnet. The magnet interfered with the fan's operation. I put a large stainless steel washer between the fan and the magnet and that helped some, but the fan was still working too hard and got really hot after only a few minutes of use.
I purchased an 80mm Arctic Cooling fan from new egg .com for 4 bucks and it works great with one hard drive magnet, no washer.
The fan is an unusual shape, but still worked out very well.
I leave my stir plate at the lowest setting, which creates a small vortex and all of my starters have been super active.

 
Reply With Quote
Old 02-20-2009, 07:28 PM   #7
XXguy
Recipes 
 
Dec 2008
Southeastern PA
Posts: 1,118
Liked 16 Times on 15 Posts


One other thought - when I tried using the bigger stirbar with my homemade plate, I had to do a little double step by turning the unit on just for a brief second, jjust enough to get the stirbar to start spinning, then turn it back on again for good. If I would just turn on the stirplate it would throw the bar almost every time. Even at the lowest speed (highest resistance) I wasn't able to just turn on the plate without throwing the bar.

Since I switched to the "X" stirbar - no problems just turning it on at whatever speed.

 
Reply With Quote
Old 02-20-2009, 07:47 PM   #8
Cookiebaggs
Recipes 
 
Mar 2007
Oak Creek, WI
Posts: 538
Liked 6 Times on 3 Posts


I created a "spin point" by sliding an O-ring from a dip tube over the stirbar.

I used a piece of electrical tape to make it fit snug and to keep it in the center. It works well giving the bar a point to spin on.



 
Reply With Quote
Old 02-20-2009, 08:52 PM   #9
keelanfish
Recipes 
 
Aug 2008
Decatur, GA
Posts: 317
Liked 5 Times on 3 Posts


1-5/8" stirbar is really big. I use a 3/4" stirbar with 1000 mL flasks and get a great vortex with the fan only spinning at about 1/2 speed.

Also, my fan has three wires. Depending on how you wire it, it can be a 5 volt or 12 volt connection. In computers, the yellow wires are 12 volt and the reds are 5 volts. I don't know if that could be the problem, but when I first hooked mine up, the 5 volt connection was not enough juice to spin the fan fast enough when the load of the stirbar was added.

Good luck!

 
Reply With Quote
Old 02-20-2009, 11:05 PM   #10
ak47clown
Recipes 
 
Dec 2008
dirty jersey
Posts: 86

well i think my next step it to pickup some smaller stir-bars. The bar i have actually has a built in pivot point in the center too. Thanks for the info guys-i'll keep you posted


__________________
:::_____________:::

Primary: Bass Ackwards Brew
Secondary:
Bottled: Magic Hat #9 clone, Amarillo IPA, Lemon Coriander Weiss
Up next: ?

 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
What Magnets/Stir Bar do you use for your Stir Plate? Stevorino Equipment/Sanitation 28 10-04-2013 05:32 PM
DIY stir plate help foxtrot Chillers & Stir Plates 17 08-25-2012 03:19 PM
Help With Stir Plate Please! tkone Chillers & Stir Plates 7 07-27-2009 03:22 PM
Stir plate help polarbearbrewing Chillers & Stir Plates 2 07-21-2008 03:39 AM
DIY Stir Plate homebrewer_99 Equipment/Sanitation 2 01-18-2007 02:06 PM


Forum Jump