Spike Brewing 12.5 Conical Fermenter Giveaway - Enter Now!

Home Brew Forums > Search Forums > Search Results

Showing results 1 to 11 of 11
Search took 0.01 seconds.
Search: Posts Made By: tolonen
Forum: General Beer Discussion 01-20-2013, 04:03 PM
Replies: 5
Views: 724
Posted By tolonen
Wow, my 2012 price was the same. 2013 4-pack...

Wow, my 2012 price was the same. 2013 4-pack price was $6.99. Greedy stores...
Forum: General Beer Discussion 06-19-2012, 04:41 PM
Replies: 70
Views: 11,459
Posted By tolonen
The LSG also has an article on the investors of...

The LSG also has an article on the investors of MBC:

Michigan Brewing Co. investors left with questions (In hindsight, some say fate was obvious)
...
Forum: Electric Brewing 11-16-2011, 04:01 PM
Replies: 8
Views: 1,782
Posted By tolonen
The SSR is a solid state relay that allows a low...

The SSR is a solid state relay that allows a low current rated device to control a high current load. In typical usage as a kettle element heater controller the PID (lowcurrent rated device) signals...
Forum: Electric Brewing 11-16-2011, 02:51 PM
Replies: 8
Views: 1,782
Posted By tolonen
A PID would be the wrong type of control for a...

A PID would be the wrong type of control for a freezer. It would short cycle the compressor and burn it out pretty quickly.

There are cheap ebay controllers that work well for freezer temp...
Forum: DIY Projects 11-10-2011, 05:54 PM
Replies: 4,097
Views: 877,826
Posted By tolonen
I did this one with parts from Walmart, easy and...

I did this one with parts from Walmart, easy and probably one of the cheapest routes. If you're planning on using it for both heating/cooling make sure you break the tab on the receptacle. He has...
Forum: Electric Brewing 11-07-2011, 06:10 PM
Replies: 44
Views: 3,516
Posted By tolonen
Another option is to wire a low power rated...

Another option is to wire a low power rated toggle switch to switch the 120VAC coil of this 2-pole contactor (which would be wired to the heating element) for a less expensive option:

Grainger...
Forum: Electric Brewing 11-03-2011, 11:35 AM
Replies: 111
Views: 23,724
Posted By tolonen
It's a 1-1/4" hole for mounting an element. ...

It's a 1-1/4" hole for mounting an element. Kal's site goes over a whole installation pretty extensively. Even supplying part numbers and places to get them. Have to go through about 10 pages of...
Forum: DIY Projects 10-24-2011, 12:17 PM
Replies: 77
Views: 49,756
Posted By tolonen
I just got one of these in the mail and checked...

I just got one of these in the mail and checked it out. Just a note, I ordered the packaged PID+40A SSR+Thermocouple 24VAC option from the ebay seller and they shipped me the 120V option. Didn't...
Forum: DIY Projects 10-16-2011, 01:12 PM
Replies: 4,097
Views: 877,826
Posted By tolonen
Or add all of your useful info to the wiki as a...

Or add all of your useful info to the wiki as a type of fermentation cabinet? Maybe add a Refrigerator/Freezer type cabinet and detail the setup of the cheap controller in there.
...
Forum: Equipment/Sanitation 08-26-2011, 01:45 AM
Replies: 14
Views: 1,283
Posted By tolonen
Works for me, gets down to $25.50 with S&S....

Works for me, gets down to $25.50 with S&S. Thanks for the heads up.
Forum: Beginners Beer Brewing Forum 08-18-2011, 01:05 AM
Replies: 43
Views: 9,990
Posted By tolonen
It's not prominently noted anywhere in the title...

It's not prominently noted anywhere in the title of the product but do note that this unit does require a 220V circuit. They do note it at the very end of description. Just wanted to give a heads-up.
Showing results 1 to 11 of 11

 
Forum Jump