Ss Brewing Technologies Giveaway!

Home Brew Forums > Search Forums > Search Results
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: jmrieger
Forum: Sponsor Giveaways 06-13-2014, 01:44 PM
Replies: 2,173
Views: 66,799
Posted By jmrieger
Do want!

Do want!
Forum: Sponsor Giveaways 01-06-2014, 01:25 PM
Replies: 3,249
Views: 91,294
Posted By jmrieger
This would look great in my basement!

This would look great in my basement!
Forum: Sponsor Giveaways 11-21-2013, 03:03 PM
Replies: 2,852
Views: 95,582
Posted By jmrieger
I'm in!

I'm in!
Forum: Brew Science 11-20-2013, 12:25 AM
Replies: 6
Views: 1,164
Posted By jmrieger
I'd like to ask an additional question about the...

I'd like to ask an additional question about the book that I can't quite reconcile. On p.68, two formulas are given for RA, one in mEq/L and a revised formula in ppm as CaCO3. Both are (summarized)...
Forum: Sponsor Giveaways 10-30-2013, 03:12 AM
Replies: 2,218
Views: 76,583
Posted By jmrieger
In!

In!
Forum: Sponsor Giveaways 07-26-2013, 08:09 PM
Replies: 2,429
Views: 95,276
Posted By jmrieger
I want it!

I want it!
Forum: Equipment/Sanitation 12-10-2012, 03:26 AM
Replies: 1
Views: 306
Posted By jmrieger
Short version: no. There are two types of...

Short version: no.

There are two types of paintball cylinders: Co2 and High Pressure Air (HPA) / compressed air tanks. The Co2 tanks are a definite no; they aren't rated to contain the pressure...
Forum: Electric Brewing 11-29-2012, 07:23 PM
Replies: 10
Views: 2,999
Posted By jmrieger
My final answer: Bad Solid State Relay. My...

My final answer: Bad Solid State Relay.

My new relay came in today. I tested by bumping to a 100% manual boil from 65*F to 125*F, then bumping manual power down to 50%. Heater cycled on/off as...
Forum: Electric Brewing 11-29-2012, 04:09 PM
Replies: 10
Views: 2,999
Posted By jmrieger
I have a new SSR coming in today, as I have the...

I have a new SSR coming in today, as I have the feeling that's the culprit. I'll post my results.

I did re-wire to run the PID off of 240 instead of sharing the ground as suggested, but that...
Forum: Electric Brewing 11-28-2012, 01:40 AM
Replies: 10
Views: 2,999
Posted By jmrieger
Ground, as I understand it. I followed...

Ground, as I understand it.



I followed the settings listed on Kal's site and left the rest of the settings at factory. Sn to 21 for RTD probe, Pb I left at 0, Filt to 5, A-M to 0, and ensured...
Forum: Electric Brewing 11-28-2012, 01:24 AM
Replies: 10
Views: 2,999
Posted By jmrieger
Wiring Help - PID / SSR Issues

Hello all,

I just finished wiring up my small panel today for my brewery, which currently consists of a single 15-gallon BIAB setup. I have a 240V dryer outlet adjacent to my brewing area, making...
Forum: Electric Brewing 11-21-2012, 03:07 PM
Replies: 157
Views: 17,611
Posted By jmrieger
Excellent. Looks like with that and the...

Excellent. Looks like with that and the manufacturer's approval I've found my preferred connectors.
Forum: Electric Brewing 11-20-2012, 11:59 PM
Replies: 157
Views: 17,611
Posted By jmrieger
Just to be clear, runs4beer, you have actually...

Just to be clear, runs4beer, you have actually used these for more than one brew session with no failures?

I only ask because I have a few sets of them that I was going to use for a non-brewing...
Forum: For Sale 11-13-2012, 06:03 AM
Replies: 5
Views: 726
Posted By jmrieger
I'll take them; PM coming your way.

I'll take them; PM coming your way.
Forum: Bottling/Kegging 11-03-2012, 05:13 PM
Replies: 37
Views: 2,714
Posted By jmrieger
Guinness Draught - 1.5 The labels are...

Guinness Draught - 1.5

The labels are heat-shrunk on, so a light slice with a razor blade and they drop right off. No soaking, no residue, no nitro widget, and great looking bottles.
Showing results 1 to 15 of 15


 
Forum Jump