The Great Bottle Opener Giveaway

Home Brew Forums > Search Forums > Search Results

Showing results 1 to 18 of 18
Search took 0.01 seconds.
Search: Posts Made By: heapyjeepy
Forum: Equipment/Sanitation 02-09-2014, 03:25 PM
Replies: 11
Views: 450
Posted By heapyjeepy
Thanks for all the ideas everyone! ...

Thanks for all the ideas everyone!



Sent from my iPad using Home Brew
Forum: Equipment/Sanitation 02-09-2014, 03:23 PM
Replies: 11
Views: 450
Posted By heapyjeepy
Sounds like the vodka would be the best bet. I'd...

Sounds like the vodka would be the best bet. I'd rather have residual vodka than antifreeze. Even if it's NSF safe. The taste can't be good... I'll have to see where a few liters of bottom shelf will...
Forum: Equipment/Sanitation 02-07-2014, 01:06 PM
Replies: 11
Views: 450
Posted By heapyjeepy
How to keep water from freezing in brew rig

:smack::smack::smack:

Did you know that water freezes in the winter?! Apparently that minor detail slipped past me this winter when i left water in my system and it froze, breaking/splitting some...
Forum: Automated Brewing Forum 12-03-2013, 02:08 AM
Replies: 2
Views: 471
Posted By heapyjeepy
I also needed a better way of knowing how to wire...

I also needed a better way of knowing how to wire my IC. So I took a picture of the top and the bottom of the IC and overlaid them with a bit of transparency one the top one. After mirroring the top...
Forum: Automated Brewing Forum 12-03-2013, 02:03 AM
Replies: 2
Views: 471
Posted By heapyjeepy
I recently tested out the power supply and found...

I recently tested out the power supply and found a nice way to hold up my main power board. The power supply makes a bit of a high frequency sound but I assume it's because of the fact there isn't...
Forum: Automated Brewing Forum 12-02-2013, 02:11 AM
Replies: 2
Views: 471
Posted By heapyjeepy
New brewtroller power box

Started working on the new setup after my brewtroller and remaining projects were completed. Here are some picks of the control box so far. I'm running a direct fire system and using a custom made...
Forum: Automated Brewing Forum 11-19-2013, 03:49 AM
Replies: 12
Views: 1,474
Posted By heapyjeepy
This is what I ended up going with. Still had all...

This is what I ended up going with. Still had all the equiptment and Brewtroller seems like an awesome user interface.

"Darn honey, I have to buy a tablet for the beer machine"

I can't wait...
Forum: Automated Brewing Forum 10-07-2013, 01:04 PM
Replies: 12
Views: 1,474
Posted By heapyjeepy
Yeah, that pic didn't work. try this: ...

Yeah, that pic didn't work. try this:

https://www.oscsys.com/projects/brewtroller/system-design/volume-measurement
Forum: Automated Brewing Forum 10-07-2013, 01:03 PM
Replies: 12
Views: 1,474
Posted By heapyjeepy
I could have used a single DP sensor but they...

I could have used a single DP sensor but they were kinda cheap and i was trying to figure out how they would respond when the water went over the second sensor port in the keggle. This was kind of a...
Forum: Automated Brewing Forum 10-07-2013, 12:53 AM
Replies: 12
Views: 1,474
Posted By heapyjeepy
Sorry yeah the linear equation is because of the...

Sorry yeah the linear equation is because of the keggle shape. Its nearly linear as far as the accuracy I'm looking for for volume.
Forum: Automated Brewing Forum 10-07-2013, 12:50 AM
Replies: 12
Views: 1,474
Posted By heapyjeepy
I used a differential pressure sensor attached to...

I used a differential pressure sensor attached to the bottom of my keggle about 2 inches off the bottom. the sensor was plugged into the analog pin on my arduino. The I added water 32 oz at a time...
Forum: Automated Brewing Forum 09-27-2013, 02:31 AM
Replies: 12
Views: 1,474
Posted By heapyjeepy
Thats the sensor that I used and it worked fine....

Thats the sensor that I used and it worked fine. I just had to calibrate it using a linear fit equation. I just added 32oz at a time and measured the output through it into excel and done.

I used...
Forum: Automated Brewing Forum 09-27-2013, 12:37 AM
Replies: 4
Views: 1,340
Posted By heapyjeepy
I looked into this for my system a while back. I...

I looked into this for my system a while back. I ran it off of a labview + ardiuno mega and it seemed to work just fine but my access to labview ended after graduation. Labview costs about $1000 to...
Forum: Automated Brewing Forum 04-20-2013, 03:57 PM
Replies: 67
Views: 10,258
Posted By heapyjeepy
I went rigth to KLD that distributes to OSCSYS. I...

I went rigth to KLD that distributes to OSCSYS. I spend a little under $300 for (3) 3way and (1) 2way valves shipped. Just got them a while ago and they work great.
Plus the customer service was...
Forum: Automated Brewing Forum 03-03-2013, 01:38 PM
Replies: 2
Views: 1,673
Posted By heapyjeepy
Automatic electronic pilot light fof propane burners

I want to set up a gas fired HERMS/RIMS system that will be heated by my Bango propane burners.

Instead of using a gas fired pilot light, could I just use an electronic pilot lighter similar to a...
Forum: DIY Projects 01-07-2013, 12:49 AM
Replies: 6
Views: 821
Posted By heapyjeepy
Some kind of tapered alignment pin like the swage...

Some kind of tapered alignment pin like the swage tool might work. Heat it up with a propane torch first, it'l make life a bit easier. There might not be a quick way to do it, so take your time.
Forum: Automated Brewing Forum 12-02-2012, 09:49 PM
Replies: 67
Views: 10,258
Posted By heapyjeepy
The rating for...

The rating for http://www.tf-valvefittings.com/goods-27.html are 0-100C (32-212F) right? So im not understanding why there is any issue with these valves?
Forum: DIY Projects 03-01-2012, 12:31 AM
Replies: 21
Views: 7,042
Posted By heapyjeepy
Pro E YES!! let me know!

Pro E YES!! let me know!
Showing results 1 to 18 of 18

 
Forum Jump