Willsellout

Gift Premium Subscription To Willsellout

Join Date:

06-17-2006

Last Activity:

02-22-2012 9:43 PM

    ABOUT ME

  • Oregon coast
  • Brewing,Bass guitar
  • US Coast Guard
  • Dan
  • Female

LATEST ACTIVITY

  • Posted in thread: Kegerator problems: foam on 04-29-2009 at 05:34 PM
    sorry, but it sounds it is still over carbed. You cant really say u dont like beer carbed at 12
    psi , if you havnt done it yet. And I mean slowly carbed beer at 12psi. I think you need to de
    carb and ...

  • Posted in thread: Kegerator problems: foam on 04-29-2009 at 05:02 PM
    I alway pour about 2 ounces out, then continue the pour in a clean cold water rinsed glass. I
    have everything from Kegconnection, and my keezer sits outside. I pour the first 2 ounces out
    cuz to cool ...

  • Posted in thread: Kegerator problems: foam on 04-29-2009 at 01:22 AM
    Thanks, I'll start with 12' and see how that goes. Hopefully it works out, I'm really tired of
    wasting perfectly good beer. In the meantime I'll purge some C02 and get back down to a semi
    normal carb ...

  • Posted in thread: Kegerator problems: foam on 04-29-2009 at 12:57 AM
    Ok so I purged all the CO2 out and then recarbed. once again I get the carbonation I want but
    with tons of foam. I even put in those short hose trouble plastic things (2) and still foam. I
    called Keg ...

  • Posted in thread: Kegerator problems: foam on 04-22-2009 at 06:14 AM
    Thanks. I'm just going to chill out and purge the carb level and wait for your kind offering
    and then work it out from there.

  • Posted in thread: Kegerator problems: foam on 04-22-2009 at 12:31 AM
    OK so I can't get the tube off of the stupid hookup so I can't get the diameter of the hose.
    Anyone know what 1.75" circumference translates into inner diameter? I think its stupid that
    they don't hav...

  • Posted in thread: Kegerator problems: foam on 04-21-2009 at 07:44 PM
    Couldn't hurt, also I flatten the curve in the top of the dipstick. I take the o-ring off, then
    put the tube back in and whack it with rubber mallet, which flattens it, then out the o-ring
    back on.tha...

  • Posted in thread: Kegerator problems: foam on 04-21-2009 at 07:38 PM
    WHile this is probably an overcarb, did you ever take off the outlet post and check the o-ring
    on the dip tube? If that doesn't seal, it will let co2 into the outlet.NOTE: release pressure
    first! :DWh...

  • Posted in thread: Kegerator problems: foam on 04-21-2009 at 07:36 PM
    :Dyou dont shake and purge at the same time! If it's over carbed, you shake. Then stop shaking.
    Pull release valve. then repeat.bad order of words there, sorry:DThat's what I did, but after
    about 5 se...

  • Posted in thread: Kegerator problems: foam on 04-21-2009 at 07:16 PM
    I leave all my kegs hooked up to gas. Just make sure you have no leaks and you're set to go.
    THere is sweet spot for everyone's setup. THere are too many variables, but most are line
    length and resist...

Following Stats
FORUM SIGNATURE
Disgrunt-Aled Brewery Primary One-empty Primary Two-Empty Secondary One-Empty Secondary Two-Empty On Tap: Hobgoblin, Coffee Stout Bottled: Arrogant Bastard clone, Summit IPA, Apfelwein
0 COMMENTS
POST A COMMENT