Toneus

Gift Premium Subscription To Toneus

Join Date:

09-27-2011

Last Activity:

05-21-2014 7:56 AM

3 Likes on 2 Posts 

    ABOUT ME

  • Wakeboarding,Hockey,Beer
  • Consultant
  • Male
  • Married
  • Atlanta
  • GA

LATEST ACTIVITY

  • Posted in thread: My coleman 70 quart extreme copper mash tun on 05-21-2014 at 09:44 PM
    I don't have a valve setup yet??? Do I need a 2in long 1/2in nipple made of brass, stainless,
    galvanized??? Does my valve need to be stainless, brass? Already failed once at Home
    Depot...Sent from my ...

  • Posted in thread: My coleman 70 quart extreme copper mash tun on 05-21-2014 at 12:56 PM
    Toneus or Kyle? What parts, exactly, did you use to create your manifold???My general parts
    list is in post #16.If you're not familiar with Shark fittings, they are quick push to connect
    plumbing fitt...

  • Posted in thread: Tony's Keezer Build on 05-29-2013 at 09:03 PM
    What height off the top did you put your taps?Juic,Here are three measurements for you...From
    wooden top (yet to add tile) to tap centerline 13 3/16"From Drip Tray to tap centerline 12
    5/16"From Drip ...

  • Posted in thread: Keezer air manifold advice on 10-25-2012 at 03:11 PM
    Also will toss in two get secondary regs. I just went from a 3 outlet manifold to a 4 reg with
    2 outlets each setup - blissful! You need multiple pressures - at least 2.After reading
    jcaudill's post, ...

  • Posted in thread: Keezer air manifold advice on 10-24-2012 at 04:54 PM
    I would suggest you start with two regulators, one for Ales & Lagers, and a second for seasonal
    beers. If you will have Wheats or higher carbonated beers at the same time as Stouts/Porters,
    then you w...

  • Posted in thread: Tony's Keezer Build on 10-18-2012 at 07:59 PM
    Are you planning to mount the CO2 tank anywhere on the keezer? I had considered going with an
    external tank on mine, but I couldn't come up with a way to mount it that doesn't look like a
    fire extingu...

  • Posted in thread: Tony's Keezer Build on 10-18-2012 at 04:37 AM
    Well your questions and pings have kicked me back into gear, thanks for that.I mentioned
    recently that I'm going through some what I've learned and how I can redesign. One of the
    things I have found m...

  • Posted in thread: Tony's Keezer Build on 10-11-2012 at 05:37 PM
    Let's bump this thread. Any more progressThanks for trying to Pimp the thread. The progress has
    been a little slow recently, but there are a couple of new things. 6 taps are now operational,
    one dedic...

  • Posted in thread: My coleman 70 quart extreme copper mash tun on 07-24-2012 at 08:28 PM
    If you don't mind me asking you both, what route did you go with the bulkhead fittings? I'm
    getting set to purchase this cooler shortly and while I won't be going the manifold route (SS
    braid w/a slit...

  • Posted in thread: My coleman 70 quart extreme copper mash tun on 07-24-2012 at 07:56 PM
    Did you have any issues with not soldering the joints? I would think you might be a loss of
    suction from all of the areas of the manifold. Copper doesn't generally press-fit very well
    together, does i...

0 COMMENTS
POST A COMMENT