thadius856

Gift Premium Subscription To thadius856

Join Date:

12-17-2012

Last Activity:

05-31-2015 4:12 AM

Referrals: 1

Likes Given: 155

662 Likes on 259 Posts 

    ABOUT ME

  • Marysville
  • Darth Vader CDA, Denny's Wry Smile Rye IPA
  • 10g Skeeter Pee, 4g Cider (1# Cane), 4g Cider (1# Turbinado), 4g Cider (1# Light Brown), 4g Cider (1# Dark Brown)
  • Nothing
  • Cream of Three Crops, Kona Fire Rock Pale Ale, Chocolate Covered BEAVR Nuts
  • 10g Black Pearl Porter, 10g Centennial Blonde, 10g Reaper's Mild, 10g Apfelwein, 5g Weak Apfelwein, 5g Franken-Ruination, 10g Haus Pale Ale
  • Male
  • Married

LATEST ACTIVITY

  • Posted in thread: Fitting a Vittles Vault with a Thermowell and Bulkhead? on 05-30-2015 at 12:38 AM
    The lid doesn't come apart. It's one piece.Do you mean how do I clean the inside of the
    bulkhead? Soap, water, and a draft line brush.

  • Posted in thread: It's Finally Done: My 10-tap Keezer! on 02-20-2015 at 04:19 AM
    I'm doubtful you can transfer the check valve, if that's what you're asking. There are several
    John Guest in-line check valves, but I doubt they're rated for gas applications. And I don't
    think they'r...

  • Posted in thread: Installing Accuflex Bev-Seal Ultra 3/16 on 02-13-2015 at 08:50 PM
    Anything less than 20' and my wheat beer pours turn foamy. I prefer to not swap lines
    constantly, since it's messy If they're not completely empty.

  • Posted in thread: Installing Accuflex Bev-Seal Ultra 3/16 on 02-13-2015 at 05:23 PM
    I like the tubing, it's just the lengths needed are a pain. I'm actually considering moving to
    a different line just to cut down the keezer clutter.But you can! All of my gas fittings are
    John Guest/M...

  • Posted in thread: Another GE 7.0 CF FCM7SUWW Keezer on 01-11-2015 at 05:01 AM
    It was, yes. And it was very adequate. I have an identical one with the same aluminum bars, but
    I added a little liquid silicone caulk between the lid and the foam to ensure there was no
    leakage.When ...

  • Posted in thread: Chest Freezer Specs and Layouts on 11-18-2014 at 06:49 PM
    I also have measurements for the Kenmore 12912 from user andrewmaixner. Thanks!I'm not super
    active here anymore (real life getting in the way), so not sure how long it will take to draw
    up and post.I...

  • Posted in thread: Chest Freezer Specs and Layouts on 11-18-2014 at 06:47 PM
    Updated main table. In the 15 cu ft class, the Kenmore 16542 is a rebadged Frigidaire
    LFFN15M5HW.Thanks to user fuzzypeach for the submission. :)

  • Posted in thread: Installing Accuflex Bev-Seal Ultra 3/16 on 06-11-2014 at 12:17 AM
    There is no need for a gasket between the John Guest 5/8" BSPP fitting and the shank. Never had
    one leak, and I have 10 of them installed.Tighten to about 12 ft-lb (approx. pulling the wrench
    around m...

  • Posted in thread: Accuflex bev seal ultra tubing problem on 06-10-2014 at 12:27 PM
    Yes. See the first relate thread in the box below.

  • Posted in thread: Chest Freezer Specs and Layouts on 06-08-2014 at 12:54 PM
    Does anybody have pictures showing how to remove the hinges on the Danby 10 cubic chest
    freezer. I am also looking for instructions on re-attaching it to the collar.ThanksSent from my
    iPhone using Hom...

Following Stats
FORUM SIGNATURE
Was this post helpful? Don't forget to click 'Like'! Thadius Miller, Project Manager -> RaspberryPints Before you build a keezer, look at this! Chest Freezer Spec Sheets and Layout Drawings (15 models and counting)
0 COMMENTS
POST A COMMENT

Newest Threads

LATEST SPONSOR DEALS