VIEW MY

Shockerengr

Gift Premium Subscription To Shockerengr

Join Date:

02-22-2007

Last Activity:

04-27-2016 5:45 PM

Likes Given: 1

27 Likes on 23 Posts 

LATEST ACTIVITY

  • Posted in thread: Homebrew Supply Keg System Giveaway on 03-01-2016 at 03:19 PM
    What the heck - an all grain Zombie Dust clone for St- Paddy's!

  • Posted in thread: Grain to Glass When Kegging-What's Your Average Time? on 01-15-2016 at 07:51 PM
    Depends on the beer, but under 10-14 days grain to glass is typical. 3-5 weeks for lagers.I
    can't hold my conicals below 45 for long periods, so it's better to just get the beer kegged
    off.If I gelati...

  • Posted in thread: controlling both fridge and freezer separately? on 01-13-2016 at 09:21 PM
    Except for the really high end fridges, here's how they work:There is usually (not always) two
    knobs to control temp.The knob for the fridge portion contains the "thermostat" and turns the
    compressor ...

  • Posted in thread: How much DME makes a batch "partial mash" on 01-12-2016 at 06:03 PM
    Partial Mash is somewhat of an arbitrary term, but in practice is really used to describe an
    extract beer that gets part of it's fermentables through a mash, usually to use grains that
    can't be steepe...

  • Posted in thread: sour IPA - any experience? on 01-12-2016 at 04:05 PM
    I've got one on tap at home, although the initial try fits more as a Sour APA than IPA.Kettle
    soured, pH of 3.75 and 40 calc'd IBU, all through whirlpool. Lots of citrus fruit hops and
    fermented with ...

  • Posted in thread: DIY glycol chilled plastic conical fermenters on 10-27-2015 at 12:58 PM
    What size conical do you use?The plastic conical referenced is 16 gallons (and typically filled
    with about 15)I have worked with the 3 and 7 bbl plastic conicals as well - it's less of an
    issue there,...

  • Posted in thread: DIY glycol chilled plastic conical fermenters on 09-27-2015 at 06:40 PM
    I've read through a bit of this post and I saw OP mention he couldn't keep the glycol system
    too much lower than his target ferm point or else when the pump shut-off there'd still be cold
    glycol in th...

  • Posted in thread: E-Herms Build 50 amp on 09-25-2015 at 05:59 PM
    augie -> need the link to flow switch you mentionedseconded

  • Posted in thread: E-Herms Build 50 amp on 09-24-2015 at 01:16 PM
    One of my Chugger pumps has been crapping out and I haven't had a chance to figure out why. It
    will be pumping along just fine and then it sounds like it's spinning with no fluids in the
    head. I'll tu...

  • Posted in thread: Self Priming Pump issues on 08-06-2015 at 05:05 PM
    It may not be adding air (assuming everything is sealed tight) but rather pulling residual CO2
    out of solution. Any restriction that induces a pressure drop (such as the prefilter) is a
    strong candida...

1 COMMENTS
Posted: 
September 25, 2014  •  05:21 PM
Hi, been reading threads on a glycol setup for 3bbl plastic fermenters. We are planning on using SS coils inside to regulate temperature. We are interested in your AC setup that is dipped in the glycol reservoir. Any pictures, tips, guides you have come up with would be awesome!

Cheers!
POST A COMMENT