VIEW MY

ryane

Gift Premium Subscription To ryane

Join Date:

11-29-2008

Last Activity:

12-16-2014 7:40 PM

Referrals: 1

5 Likes on 5 Posts 

    ABOUT ME

  • Washington
  • Brewing,Backpacking,Fishing
  • Yearly Lambic and Flanders:rnBelgian Table Beer:rnOud Bruin (Sour Keg Mash):rnKentucky Common:
  • Lazy Lambic:rnLambic, 1yr, 2yr, 3.5yr:rnFlanders Red:rnCorn Lager:rnCorn Kolsch:rnB Weiss:rnBugfarm Sour:rnBiere de Garde with Barbera Greapes:rnGosebier fermented with Sauerkraut Dregs:
  • Who uses them?
  • Gueuze:rnStill Lambic:rnCherry Melomel:rnSmoked Ale:rnBrett L Brown:rnF Red:rnCherry Gose:rnB Weiss:rnRhubarb B Weiss:rn21.5% Impy Stout:
  • Schwarzbier:rnHarvest Rye Mild:rnRobust Porter:rnB Weiss:rnCherry Smoked Malt Ale:rnHoppy Wit:
  • Male
  • Married

LATEST ACTIVITY

  • Posted in thread: Stepper Motor Butterfly Valve on 11-27-2014 at 03:02 PM
    Yeah I won't be home till Friday to do so. I also cut the threads off completely and tried to
    weld a fitting on. The problem is they are made of crap metal and I couldn't get a good arc.
    Sent from my ...

  • Posted in thread: Upside Down Keggles? on 11-26-2014 at 11:00 PM
    Awesome. Thanks!Case is bloody huge.Where'd you get the case, and how much did it set you back?

  • Posted in thread: Stepper Motor Butterfly Valve on 11-26-2014 at 09:46 PM
    Something that detoured me from doing this is, I took a bit and ground down one side of the
    threads in an extra valve. Found a air pocket at the bottom were it tappers. Might just be one
    bad valve. Se...

  • Posted in thread: Stepper Motor Butterfly Valve on 11-26-2014 at 05:40 PM
    Currently I have 10 12v threaded valves on my brewstand, everything is tri clover and im ready
    to remove all threads finally. What do you guys think about attaching a stepper motor to
    butterfly valves...

  • Posted in thread: Using wood for a control box.. Smart or Dumb on 11-26-2014 at 05:35 PM
    In a wood box, what happens in a wire is shorted to the wood? It doesnt blow the breaker, so
    you have less protectionlook on ebay for boxes and dont build your controller in a wood boxWhy
    skimp on spe...

  • Posted in thread: Speakon-Like connector with NPT thread? on 11-26-2014 at 05:30 PM
    Im tyring to find something like a neutrick speakon connector that instead of panel mount has
    NPT or similar threads on the back side. Im hoping to find something like this because it will
    make it a l...

  • Posted in thread: Upside Down Keggles? on 11-26-2014 at 05:23 PM
    Hey Ryane,Do you have any suggestions for a locking receptacle for the pumps? I'm looking at
    this one but it says 2 pole, will it work? means that is has 2 conductors (H-H or H-N = the
    same thing) an...

  • Posted in thread: Camco 5500W through a 1" hole? on 11-15-2014 at 03:29 AM
    A 1" conduit punch has an actual diameter of 1.36"

  • Posted in thread: Easily Removable Temp Probe on 11-11-2014 at 12:48 AM
    Hi all. I have an electric brewery with my temp probes for my BCS-460 running through standard
    NPT compression fittings (all purchased from Brewers Hardware). No big deal. But, I also have a
    Megapot t...

  • Posted in thread: Upside Down Keggles? on 11-09-2014 at 03:36 PM
    Thanks! Doesn't look like that one is locking. If I put this on the bottom of my control panel
    what's the likelihood that it falls out?It is locking, I used one on my panel!Marinco tends to
    be much ch...

0 COMMENTS
POST A COMMENT

Newest Threads

LATEST SPONSOR DEALS