rollinred

Gift Premium Subscription To rollinred

Join Date:

01-02-2008

Last Activity:

05-06-2014 9:30 PM

Likes Given: 1

10 Likes on 7 Posts 

    ABOUT ME

  • Traverse City, MI
  • Snowmobiling,Guns,Brewing
  • Led Zep
    GnR
  • Saving Private Ryan
  • Liberty and Tyranny by Mark Levin
  • Male
  • Married

LATEST ACTIVITY

  • Posted in thread: HERMS Help on 09-01-2013 at 02:19 AM
    Well, I gone done it. Bobby's got ANOTHER order from me for the rest of the cam lock/barb
    fittings I need to set up this HERMS coil. I really really really.... really, need to stop
    building equipment ...

  • Posted in thread: HERMS Help on 08-30-2013 at 02:18 AM
    Wow, this discussion got where it needed in a hurry. Thank you! Thought after the first few
    days it wouldn't get anywhere but lost. I don't know 'bout you Yoop, but my Michigan blood
    can't take this h...

  • Posted in thread: HERMS Help on 08-30-2013 at 12:32 AM
    Thanks Yoop! That is exactly what my question was. What I am going to do is build a lid for my
    HLT that will hold the HERMS coil and a stirrer motor. This whole lid will just lift off when
    it's not in...

  • Posted in thread: HERMS Help on 08-30-2013 at 12:05 AM
    Kal,I think I understand what you are saying but I would like to clarify it. What I think is
    getting a little lost here is that I am simply looking to see which RTD/temp sensor people are
    using to con...

  • Posted in thread: HERMS Question on 08-29-2013 at 05:26 PM
    I always drain my runnings into a couple of buckets and dump them back into the boil kettle
    after I have sparged. So it kind of goes something like this:- Heat 8 gallons or so of water
    (depending on g...

  • Posted in thread: HERMS Question on 08-28-2013 at 02:31 AM
    billr1,You're in the same situation I'm in and I've decided to go along your questioned path.
    Running through the lid is going to give me a much more versatile piece of equipment. I don't
    want to, nor...

  • Posted in thread: HERMS Help on 08-24-2013 at 04:55 AM
    Just bought a chugger pump and cam lock setup. Realized I had 25' of leftover copper coil and
    got to thinking that I could be just a couple steps away from a HERMS rig. I'm wondering how
    you all fire ...

  • Posted in thread: Weldless Triclover Element? on 08-23-2013 at 02:35 PM
    Bobby,I just placed an order with you but now wish I would have waited for a bit for you to
    release this thing. Exactly what I have been looking for. Might try the silver soldered one on
    my Blichmann ...

  • Posted in thread: Outdoor e-brewing on 08-23-2013 at 03:12 AM
    Sure. Use an outdoor rated enclosure and put in a properly protected (GFCI) breaker. I'm going
    to tell you right now that you "need" to run a 50 amp service. Need in parenthesis because
    eventually you...

  • Posted in thread: Electric Noob starting E-brewery. Help pls! on 08-21-2013 at 02:06 PM
    Man, you're scaring me knowing that some day you will power up that panel ;)I do believe the
    center wire of that cord is ground. Usually they will have some different marking or physical
    appearance. B...

Following Stats
FORUM SIGNATURE
Kat Sass Brewery
0 COMMENTS
POST A COMMENT