P-J

Gift Premium Subscription To P-J

Join Date:

03-07-2010

Last Activity:

09-19-2014 10:42 AM

Referrals: 1

Likes Given: 441

250 Likes on 201 Posts 

    ABOUT ME

  • Charlotte, NC
  • Single

LATEST ACTIVITY

  • Posted in thread: Where to wire rheostat and what kind to get? on 09-09-2014 at 08:46 PM
    Here is a post that has a diagram that should fit your needs. It uses a SSR for HLT control and
    a SSVR for BOIL control. SSVR and its associated rheostat is a product of Auber Instruments:

  • Posted in thread: Best PID? on 09-04-2014 at 10:45 PM
    And mostly provide by a single man!:oEdit:Another point: What you say is real. The product is
    real, supported and reliable!

  • Posted in thread: Best PID? on 09-04-2014 at 10:19 PM
    Auber Instruments PID 2352 temp controller. Lots of diagrams on this forum for set ups.

  • Posted in thread: List of PJ Electrical Diagrams on 09-03-2014 at 01:51 PM
    P-J, should I be switching on and off the positive signal wire only or should I switch the
    negative signal as well? The negative signal is like a ground right and doesn't have power
    normally in a DC c...

  • Posted in thread: List of PJ Electrical Diagrams on 09-03-2014 at 11:30 AM
    P-J, I have a similar setup with a PID and a rotary knob, but would like to use the same SSR to
    control my element. Space is a concern in my salvaged control panel and so I'd like to use only
    one SSR ...

  • Posted in thread: SSR base material? on 09-01-2014 at 01:10 PM
    I'd suggest that you get the thermal grease offered by Auber Instruments:Click this linkIt is
    very reasonable and specifically made for the task. If you had ordered the SSR & heatsink from
    them, they ...

  • Posted in thread: List of PJ Electrical Diagrams on 09-01-2014 at 12:32 PM
    Deece, This diagram is what you are looking for (I think).Switch 1 is set up to control the
    input to the SSR or the SSVR so that only one would be used at a time.Hope it helps you.P-J

  • Posted in thread: Help with RIMS controller wiring diagram on 08-30-2014 at 11:26 PM
    Be careful with the above Radio Shack components, rated at only 300 volts, most 20 amp
    components and wiring rated to 600 volts, just an FYI for anyone perusing this threadThanks for
    that. You must ha...

  • Posted in thread: Help with RIMS controller wiring diagram on 08-30-2014 at 10:01 PM
    P-JYour schematics have been very helpful. I'm sure you are beseiged with questions and if you
    could indulge a few more regarding your 5500W-BIAB-30d11 design, I would appreciate it. First,
    did you bu...

  • Posted in thread: List of PJ Electrical Diagrams on 08-29-2014 at 06:47 PM
    I think that may be what I'm looking for, i plan on using the same element for both, do I need
    separate contactors still or just switching the trigger to the same contactor? Use this single
    pole doubl...

2 COMMENTS
Posted: 
November 23, 2013  •  01:36 PM
http://www.homebrewtalk.com/f170/ehlt-recirulation-pump-stir-motor-262170/

I just saw your stir motor and it looks wonderful. $18 for the 63rpm motor is great. You mentioned that the top came from walmart. The build looks simple. What keeps the top from turning? I would love to see a thread on it with pics
 
Posted: 
April 6, 2014  •  11:14 PM
You probably don't remember me, but you helped me with wiring my system over the phone a couple of years ago. Just wanted to say thank you and that the system has been working great!
 
POST A COMMENT