MrShake

Gift Premium Subscription To MrShake

Join Date:

07-23-2006

Last Activity:

04-28-2016 1:44 PM

Likes Given: 10

8 Likes on 8 Posts 

    ABOUT ME

  • Midwest's Hank's Hefe
  • Air
  • None
  • Brewer's Best Red Ale (I think its infected)
  • Male
  • Single

LATEST ACTIVITY

  • Posted in thread: Anyone take a Kal Clone and... on 05-03-2016 at 03:07 AM
    It does and I appreciate your time looking at this - it sounds like this is going to be quite
    tricky to accomplish as I *do* want to keep the existing hardware PIDs so that I can use the
    panel in full...

  • Posted in thread: Anyone take a Kal Clone and... on 04-28-2016 at 02:30 AM
    So I took a quick look (ended up being a VERY busy day) and assuming you want to eliminate the
    PIDs completely (not have the option for both) then you are looking at simplifying quite a bit.
    I'll have...

  • Posted in thread: Anyone take a Kal Clone and... on 04-28-2016 at 02:25 AM
    Yea, someone was working on an RTD board, but it never came to production. The One Wire probes
    are not too expensive and are plug and play

  • Posted in thread: Anyone take a Kal Clone and... on 04-27-2016 at 04:05 PM
    MrShake, here are a couple of pics... A couple more are in the process of hitting Flickr... My
    rats nest wiring job may not help much but like I said it's a stock Kal clone minus the safe
    start interl...

  • Posted in thread: Anyone take a Kal Clone and... on 04-26-2016 at 03:02 AM
    Okay... so I'd replace my existing on/off switches with three-ways... the element control might
    be a bit difficult in that case though as that's already a three-way (boil/off/hlt), but maybe
    use the '...

  • Posted in thread: Anyone take a Kal Clone and... on 04-25-2016 at 11:46 AM
    Well, yes, but no. (Again, I'll speak for BrewTroller as thats my expertise). You would
    probably not use the hard switch, but many folks do use an expansion board like the RBGIO to
    have 3 way switchte...

  • Posted in thread: Anyone take a Kal Clone and... on 04-22-2016 at 10:15 PM
    That should be very simple. Kal Clones just use PIDs, you just need to connect the same outputs
    to the outputs on the controller you decide on. Not difficult at all!!I could help you get
    started with ...

  • Posted in thread: In Person DLD FT: Mystery Box ISO: Mystery Box on 04-19-2016 at 02:01 AM
    Hey Guys, I'm going to be at Dark Lord Day, looking to do a mystery box trade or two while I'm
    there.Whats a mystery box? Its a "B-list" and local beer trade that is a mystery. I put
    together a box of...

  • Posted in thread: Computer controlled Vs. Component/manual Controlled? on 04-19-2016 at 01:55 AM
    That's just the way he does it. You can start/stop processes using a switch or push button on
    the BCS if you wish.The reality with any of these systems is that you need to see something for
    feedback o...

  • Posted in thread: Computer controlled Vs. Component/manual Controlled? on 04-15-2016 at 03:38 PM
    The BCS can be stand alone as well. Once I start the Process, I can control it without a
    Computer, but if you want to see what you are doing, it is easier with a computer. I actually
    have the computer...

Following Stats
FORUM SIGNATURE
MrShake - Top Hat Brewery and Tapworks Owner of BrewTroller
0 COMMENTS
POST A COMMENT