mattd2

Gift Premium Subscription To mattd2

Join Date:

09-24-2009

Last Activity:

12-08-2016 4:15 AM

Likes Given: 66

319 Likes on 254 Posts 

    ABOUT ME

  • Male
  • Married
  • Papamoa
  • New Zealand

LATEST ACTIVITY

  • Posted in thread: working on an eltric brewery, simple wiring question on 12-07-2016 at 11:55 PM
    Wire in parallel, the commons tie together and the hot to each switch or output driver.There is
    no way to wire them in series and still communicate useful information, the lights will either
    all be on...

  • Posted in thread: Tri Clamp End Cap on 12-06-2016 at 12:15 AM
    looks like it is for a DIN fitting like this... it is a DIN/RJT screw type sanitary fitting.
    Definately will not fit a Triclover fitting. In the case of your photo that is not a Triclover
    valve :)

  • Posted in thread: We introduce you to the Amazing Homebrew Competition on 11-30-2016 at 08:13 AM
    I think it would be funny if someone in Korea just wants lots of good beer, so they fake a
    competition.I was wondering if South Korea had insanely restrictive alcohol laws /
    prohibition... turns out i...

  • Posted in thread: We introduce you to the Amazing Homebrew Competition on 11-30-2016 at 12:46 AM
    I just checked UPS with some quick estimates, which may be wrong:12 bottles in a 12x16x10 box
    at 15# is $253.40 ~ $21.12/bottle24 bottles in a 24x16x10 box at 30# is $386.20 ~
    $16.09/bottle48 bottles ...

  • Posted in thread: I'm F'in done with SSR's on 11-14-2016 at 10:32 PM
    Never be afraid to buy a more expensive/quality product. Buying the cheapest SSR you can find
    on eBay greatly increases the changes that you'll be replacing it more than once which doesn't
    really save...

  • Posted in thread: I'm F'in done with SSR's on 11-14-2016 at 10:19 PM
    It was a Fotek that failed after two years,I thought that was pretty good so I bought a Fotek
    replacement. That was the one that the LED light worked with constant power out.After that I
    switched to t...

  • Posted in thread: Question for the electricians--ok to run a 3-wire power cable from a 4-wire outlet? on 11-10-2016 at 11:53 PM
    That sounds a bit suspect - after all most factories only have a single feed coming into their
    buildings so it is going to be on the same feeder circuit from some point. And motor / element
    is not the...

  • Posted in thread: Did I score at the habitat re-store? on 11-10-2016 at 11:47 PM
    Maybe...? it is probably just a standard 1" NPT thread. Outside diameter of a 1" NPT is 1.315"
    (i.e. pretty close to 1 3/8" especially if you are measuring with a ruler/tape measure :)

  • Posted in thread: Teeing MLT and BK outlets together on 11-10-2016 at 11:32 PM
    If it is before chilling the wort is close to boiling at that point, no? , so is sanitation a
    concern? I will be running into cfc to fermenter so cool wort won't be between bk and mlt.The
    concern is "...

  • Posted in thread: Question for the electricians--ok to run a 3-wire power cable from a 4-wire outlet? on 11-10-2016 at 11:23 PM
    If the ground attaches to the chassis then it is fine. If it is used in place of a neutral then
    it is not fine.A single UL test session can cost upwards to $25K, I am surprised that they
    would pay thi...

Following Stats
0 COMMENTS
POST A COMMENT