VIEW MY

kleinishere

Gift Premium Subscription To kleinishere

Join Date:

04-08-2012

Last Activity:

04-16-2013 9:14 PM

Likes Given: 1

    ABOUT ME

  • Single
  • Los Angeles
  • CA

LATEST ACTIVITY

  • Posted in thread: Dual regulator w/ MFL - Couple Questions on 04-11-2013 at 03:45 AM
    A follow-up email to the Taprite customer service department was quickly replied to and
    confirmed that this Taprite T752HP model does have check-valves pre-installed (as listed on
    their website), as a...

  • Posted in thread: Dual regulator w/ MFL - Couple Questions on 04-10-2013 at 05:19 AM
    Thanks a lot for the replies / advice. Ended up going w/ the Taprite T752HP dual body regulator
    and bypassing a potentially slippery road w/ the pictured regulator.According to Taprite's
    website, the ...

  • Posted in thread: Dual regulator w/ MFL - Couple Questions on 04-08-2013 at 06:17 AM
    Closing in on the last steps of my first keezer and ran into a couple issues/questions w/ my
    dual regulator (picture attached). Trying to figure out what direction to take and if there's
    any options I...

  • Posted in thread: WTB: (1) 1/4" Barbed Tee for CO2, (2) Hose Barbs w/ Check Valves on 05-18-2012 at 07:03 PM
    I'll mail you a few barbed T (Chrome plated brass) if you throw me a couple dollars for
    shipping. Just pm me.PM'd. Thanks!If anyone has some extra hose barbs w/ check valves, would
    love to grab those ...

  • Posted in thread: WTB: (1) 1/4" Barbed Tee for CO2, (2) Hose Barbs w/ Check Valves on 05-18-2012 at 01:07 AM
    I'm hoping to add a couple more kegs to my set up and am wondering if anyone has any of the
    following lying around (used or new). I'd offer $20 shipped for the whole lot, if so. Brass or
    stainless ste...

  • Posted in thread: Seeking Confirmation on CO2 Regulator Valves on 05-18-2012 at 12:41 AM
    as long as one check valve between the regulator and any kegs, it doesnt matter very much if
    there isnt one between the kegs themselves. it is nice to have one ball valve and check valve
    on each gas l...

  • Posted in thread: Best place to buy Perlick's, shanks? on 05-16-2012 at 10:15 PM
    You're still going to need a regulator and co2 tank, and a manifold if you are planning more
    than 1 keg. Oh, and a kegSo you'll need at least This kit from the Beer Tap Store for 113 or
    you could get ...

  • Posted in thread: Seeking Confirmation on CO2 Regulator Valves on 05-16-2012 at 08:11 PM
    sounds good. you can also buy 1/4" stainless steel 'T's and just have one end going to the
    regulator, and the other two go out to your gas disconnects.that Y splitter is essentially the
    same thing, bu...

  • Posted in thread: Seeking Confirmation on CO2 Regulator Valves on 05-16-2012 at 09:51 AM
    Hi all,I'm about to place an order for my 3 keg system but am hoping for your all's
    confirmation regarding CO2 regulator valves.A photo of my dual regulator is attached to the
    post.I would like to mak...

  • Posted in thread: Best place to buy Perlick's, shanks? on 05-16-2012 at 06:58 AM
    I've been doing some similar research for a keezer project. I'm looking to get into kegging, so
    the *whole* package is what I have in mind.The Beer Tap Store had this combo for $72.95 (plus
    shipping):...

0 COMMENTS
POST A COMMENT

Newest Threads

PHOTO OF THE DAY