kladue

Gift Premium Subscription To kladue

Join Date:

12-28-2006

Last Activity:

09-21-2014 6:00 PM

47 Likes on 43 Posts 

    ABOUT ME

  • Industrial Process Instrumentation installer
  • Kevin LaDue
  • Capitol Brewers Homebrew Club
  • Male
  • Married
  • Turner, Oregon
  • Oregon most of the time now

LATEST ACTIVITY

  • Posted in thread: need help with a wiring diagram....please! on 09-06-2014 at 02:39 AM
    Go with another VR8200, LP conversion valves for Banjo burners from Brewers hardware, a
    Bernzomatic 200K LP 2 stage regulator from Lowes, Q314 & Q345 pilots and transformer from PEX
    Supply. By firing ...

  • Posted in thread: need help with a wiring diagram....please! on 09-05-2014 at 03:26 AM
    Here is a link to a diagram
    https://picasaweb.google.com/110297595278760536729/PanelWiringDiagram?noredirect=1#550797969035
    0514498,as to the transformer, if mounted inside a control panel I would sugg...

  • Posted in thread: Intermittent pilot system help please on 08-15-2014 at 03:38 AM
    You will need a bigger enclosure to provide room for switches and transformer, something more
    like 10X12X6 would be appropriate, don't start too small and lament the fact that there is not
    enough room...

  • Posted in thread: Intermittent pilot system help please on 08-14-2014 at 03:24 AM
    For an enclosure something along the lines of a NEMA 12 or 4 would work as you will spill
    something on it before you can say it will never happen. With the honeywell valves you will
    need a 120-24VAC t...

  • Posted in thread: Intermittent pilot system help please on 08-13-2014 at 03:20 AM
    A quick question, you want to go high pressure or low pressure propane, or NG. A couple things
    are universal, the Y8610 ignition module and the Q345 pilot burner. If you want to go the high
    pressure L...

  • Posted in thread: Please Help - BCS 462 to Honeywell VR8200a on 07-20-2014 at 03:43 AM
    Sialas, Sorry about the delay, about the only things that could happen are the internal
    regulator is missing a spring (the one changed for conversion), or the inlet pressure has
    tripped the over press...

  • Posted in thread: Please Help - BCS 462 to Honeywell VR8200a on 07-08-2014 at 03:44 AM
    SIlas, pull the burner orifice fitting and test the opening size, should be able to fit a 5/64
    - 3/32" drill bit, if not be gentle and drill it out. If you want an off the shelf
    orifice/valve assembly...

  • Posted in thread: Please Help - BCS 462 to Honeywell VR8200a on 07-02-2014 at 03:45 AM
    SIlas, Lets start on the gas side first, you need the low pressure orifice for the Banjo burner
    if you have not already installed one. If you have not switched to an orifice with a 3/32"
    opening you n...

  • Posted in thread: Automating Grain-In on 05-30-2014 at 03:40 AM
    Here is the mash tun with stirring motor and paddles
    https://picasaweb.google.com/110297595278760536729/WetTestProgressPhotoS?noredirect=1#522529886
    1192897346. Motor is a 60 rpm gear motor with a 1/2"...

  • Posted in thread: Screw conveyor for Phase 2 system on 05-29-2014 at 03:27 AM
    The inner pipe is 1-1/4" type K copper, the spiral is 1/4" Od copper tube on 2" spread, soft
    soldered with silvabrite 100, and outer is 2" Od SS tubing. Shafts were 1/2" round stock with
    washers welde...

0 COMMENTS
POST A COMMENT