VIEW MY

dutch-brew

Gift Premium Subscription To dutch-brew

Join Date:

05-06-2009

Last Activity:

08-19-2014 5:44 PM

1 Likes on 1 Posts 

    ABOUT ME

  • s.e.missouri
  • just getting into the homebrew thing.. hope i'll like it, which, i like beer so i'm sure i'm fine :)
  • homebrewing?
  • anything that rocks!
  • witbeer,
    maybe a leffe or dubbel
  • oktoberfest,
    honey wheat
  • pilsener ale,
    autumn amber ale
  • grape mead
    apfelwein
    orange mead
  • honey amber ale,
    california steam
  • Male
  • Single

LATEST ACTIVITY

  • Posted in thread: Using a pasta maker to mill grain. on 02-26-2011 at 05:47 PM
    I just cut them straight in the length of the rollers. Even did it with the rollers in place in
    the pasta maker. Use the re-inforced discs. Make sure to wear eye-protection! Those blades are
    notorious...

  • Posted in thread: Using a pasta maker to mill grain. on 02-26-2011 at 05:20 PM
    Ahh. I've had to re-gouge my rollers multiple times, I took a dremel and cut grooves all along
    the rollers. They are nice and rough, and never had to re-gouge my rollers. Here i am a few
    hundred #'s o...

  • Posted in thread: Fermcap S conclusion? on 02-06-2011 at 02:38 PM
    I use about 10-12 drops of Baby Gas Drops in the BK to prevent boil-over.What are these Baby
    Gas Drops you mentioned? Is it similar to the fermcap/ defoamers? Is it cheaper/more easily
    available? More...

  • Posted in thread: Fermcap S conclusion? on 02-06-2011 at 02:35 PM
    Seems to carry over from starter boil to starter ferment, but not from batch boil to batch
    ferment. I guess a lot comes out in the hot break and hops (I whirlpool).Do you use a
    stir-plate? If that wou...

  • Posted in thread: E-HLT question (water heater element/plastic cooler) on 02-06-2011 at 02:29 PM
    I have a (very long) 5500W element ran through the side of my cooler without any leakage/issues
    at all, so it is possible. Wouldn't see why yours couldn't seal up since mine has more strain
    on it due ...

  • Posted in thread: Fermcap S conclusion? on 02-01-2011 at 01:15 PM
    With a stir-plate I never get krausen in the flask, idk if this is normal.I am curious how
    much people use for primary fermenting, though. Doing my first corny keg primary today or
    tomorrow!Thanks fo...

  • Posted in thread: Fermcap S conclusion? on 02-01-2011 at 12:14 PM
    Ok, been going through all the threads a bit, and was hoping to summarize the info and make
    sure i got this straight.Fermcap S (or similar foam controls)-can add to the BK. About 6+ drops
    for 5 gal. b...

  • Posted in thread: supply cord connectors on 01-24-2011 at 03:42 PM
    They will work. Are you measuring your voltage under load?(doubtful) Open circuit voltage will
    read higher than then actual loaded.No, not under load. Didn't think about that.

  • Posted in thread: supply cord connectors on 01-24-2011 at 02:30 PM
    Have the e-keggle up and running now for a while, but was wanting to be able to take my supply
    cord off to make my electrical toolbox more mobile. I have one of those GFCI cords off ebay on
    it, and it...

  • Posted in thread: 240VAC Toolbox Control Panel with Pics on 10-10-2010 at 04:30 PM
    Oh man, i am an idiot.. looking at so many of these threads i am getting 'em all switched
    up..sorry

0 COMMENTS
POST A COMMENT

Newest Threads

LATEST SPONSOR DEALS