doubleb

Gift Premium Subscription To doubleb

Join Date:

08-03-2007

Last Activity:

11-12-2012 8:12 PM

1 Likes on 1 Posts 

    ABOUT ME

  • Milford, CT
  • robb

LATEST ACTIVITY

  • Posted in thread: CO2 tank in Fridge: Pressure reading on 11-14-2010 at 01:06 PM
    my tank is reading is 750 at room temp and now its right on the line between red and white
    which is 400 at 40 degrees F on my regulator. Its a 5lb tank. Should I be looking for leaks or
    just keep an e...

  • Posted in thread: How much CO2 leaking is acceptable? on 11-05-2010 at 10:55 AM
    Hi I just kegged for the first time. My tank just capoots(it was used so I'm not sure how much
    there was to begin with). Is the a safety issue for me, my kids, or my cat if there is a leak
    and a lot h...

  • Posted in thread: Jay Leno Should Retire So Conan Doesn't Walk on 01-25-2010 at 03:07 AM
    It would have been nice to see Leno do the honorable thing. He's had five years to figure out
    what to do. Conan is the man for the job. I was hoping that this was some sort of NBC sick jock
    to get som...

  • Posted in thread: Exploring "no chill" brewing on 09-26-2009 at 03:38 AM
    Hey all I'm taking the plunge into No Chill. I just upgraded my 5 gallon kettle w/ a ball valve
    and a bazooka screen and I got the high temp. tubing (up to 275*). I also got two 2.5 gallon
    cubes from ...

  • Posted in thread: who could drill my kettle hole on 09-21-2009 at 11:15 PM
    Good job! You would have felt like a Wuss if you would have had someone else do it for
    you.You're probably right. I'd also feel like my wife made my decision for me. Doing it myself
    was the best way c...

  • Posted in thread: who could drill my kettle hole on 09-21-2009 at 11:12 PM
    Wasn't so bad, was it? The drill bit walking around is why I recommended hitting it with a nail
    punch; didntcha listen to me? ;)The word punch freaked me a bit ;), so I stayed away from it
    this time. ...

  • Posted in thread: who could drill my kettle hole on 09-21-2009 at 11:52 AM
    :ban: :ban: :ban:Here is the wrap-up...It is done. I went to my local Lowe's and got a Unibit
    and a titanium pilot bit. I ended up putting my knee inside the kettle and knelt on the kettle
    which was o...

  • Posted in thread: who could drill my kettle hole on 09-19-2009 at 07:07 PM
    The stuff came in today. I got to get over to the hardware store and pick up the parts. Hoping
    I can bust out the drill tomorrow or Monday. Will post results. Thanks for all the advise.

  • Posted in thread: who could drill my kettle hole on 09-18-2009 at 07:18 PM
    If you have a dirty mind(like I do) the title of this thread is hilarious.... :cross:Oh...
    c'mon I just need my hole drilled. Nothing dirty about that. ;)

  • Posted in thread: who could drill my kettle hole on 09-18-2009 at 03:34 PM
    Is the kettle aluminum or stainless? If aluminum you can punch a starter spot instead of
    drilling. I see no need for masking tape or Pam. If Alum, it's very soft and easy to drill, I
    did mine with a s...

Following Stats
FORUM SIGNATURE
Next: Primary:Hoppiness Secondary: Kegged:Brown Ale Bottled:
0 COMMENTS
POST A COMMENT