CodeRage

Death by Magumba!

Gift Premium Subscription To CodeRage

Join Date:

08-22-2007

Last Activity:

09-22-2014 12:10 PM

Referrals: 1

Likes Given: 5

31 Likes on 17 Posts 

    ABOUT ME

  • Melbourne, Fl
  • Electrical Engineer
  • Jason Vreeland
  • Just about anything
  • Male
  • Single

LATEST ACTIVITY

  • Posted in thread: Electrical Primer for Brewers on 03-04-2014 at 02:09 PM
    The reason why I used the general wiring table versus the chassis table was to keep it simple.
    I dare not assume that the vast majority here know the difference between different insulator
    types and h...

  • Posted in thread: Electrical Primer for Brewers on 04-26-2011 at 12:23 AM
    So, a quick general theory question....Basically, I'm confused.No worries man, if its a new
    concept and can be difficult to get your head around it.Lets call the two hots L1 and L2 then
    the Neutral. i...

  • Posted in thread: HOW TO: Wire an Auber SYL-2362A2 PID for a Fridge on 04-25-2011 at 12:36 AM
    Does this completely cut the electricity to the freezer? Do you think it will cause issue to
    the compressor after come time of off and on?Nope, thats how the original thermostat in the
    freezer works. ...

  • Posted in thread: Temperature Monitoring and Control with Arduino on 04-05-2011 at 06:39 PM
    boil kettles and mashtuns, dont see any copper fermenters though.

  • Posted in thread: Money!!! on 04-01-2011 at 03:47 PM
    Well, the best bit of advice I can offer is to quit counting :)I've had to acquire my stuff
    slowly over time. Start simple and get something working and then go from there.

  • Posted in thread: what is your occupation on 03-30-2011 at 09:23 PM
    Well. I'm an engineer by degree in a very engineering oriented company but I no longer do much
    engineering and have forgotten at least half of what I knew....so I guess I'm a half ass
    engineer and hal...

  • Posted in thread: Is this the right kind of GFCI? on 03-24-2011 at 10:57 PM
    They wont cancel each other out. I dont remember seeing anything in the NEC that says you cant
    either. From the people Ive talked to they seem to me prone to nuisance trips, but their
    problem may have...

  • Posted in thread: Is this the right kind of GFCI? on 03-22-2011 at 06:30 PM
    You can buy a 60A GFCI spa panel for the same price as that little gizmo.The reason why you
    need a contactor for that thing is because it only has a single pole contact. Once a ground
    fault is detecte...

  • Posted in thread: Let's talk dc motor control on 03-15-2011 at 11:48 PM
    yeah, three phase is preferred because there is virtually no slip in the motor, tons of torque.
    With the VFD you can change the frequency of the AC wave form wich translates to spindle speed.
    That and...

  • Posted in thread: Let's talk dc motor control on 03-15-2011 at 10:58 PM
    Does it need to be DC?If so you're looking at large DC servos and servo controllers.If these
    are for Mills and Lathes, look into some small 3 phase motors.3phase motorsand you can find
    single phase in...

FORUM SIGNATURE
Brutus 20e build | Electrical Primer for Brewers | Auber SYL-2362A2 PID Install & Config So as I am walking out the door this morning I think to my self: "self, going to work on Monday is like knowing you're going to get kicked in the nuts. You just don't know when or by who"
0 COMMENTS
POST A COMMENT