Gift Premium Subscription To audger

Join Date:


Last Activity:

05-22-2014 5:38 PM

Likes Given: 1

44 Likes on 42 Posts 


  • CT
  • Single


  • Posted in thread: 3 stage water filtering system on 05-22-2014 at 07:14 PM
    I agree for the most part, but this is HIGHLY dependant on your water source: But not many
    people actually need a filter, as usually our water supplies aren't loaded with sediment and
    off-flavors. I w...

  • Posted in thread: Induction Burner on 05-22-2014 at 07:03 PM
    the time it takes to heat X-amount of liquid (and thus, the 'recommended amount' of power)
    depends on the wattage of the heater, and the size of the brew. If you were brewing 1 ounce of
    beer at a time...

  • Posted in thread: 3 stage water filtering system on 05-22-2014 at 06:47 PM
    I use a cheap DIY '2-stage' filter for brewing. The first stage is a 5-10 micron sediment
    filter, and the second is a 0.5micron nominal carbon block filter for chlorine and chemicals.
    true, carbon won...

  • Posted in thread: Temp Control on 05-22-2014 at 06:37 PM
    I was hoping to have something where if it get's over 68 it kicks on the freezer, if it gets
    under 66 it kicks on the heating element(haven't picked one out). Is this possible with this
    unit?that prog...

  • Posted in thread: Does the volume of beer in my keg affect the pressure needed to carbonate? on 05-22-2014 at 06:20 PM
    No, it doesn't.Think of it this way. The amount absorbed into the beer is a function of a)
    surface area and b) pressure. Whether there is 1 gallon or 5 gallons in the keg, the surface
    area is the same...

  • Posted in thread: Converting volumes of CO2 to PSI? on 05-22-2014 at 06:07 PM
    And sorry, I don't mean to harp on this, but isn't pressure dependent on the volume of the
    vessel? So wouldn't a 1 gallon container of beer have less internal pressure than a 5 gallon
    container of bee...

  • Posted in thread: Beer lost flavor after a few days in the keg. on 05-22-2014 at 05:55 PM
    CO2, and the amount used, certainly imparts its own flavor profile into a beer. too much and
    the sting/bite of the gas can certainly overpower other flavors in the beer.its good that you
    found the cau...

  • Posted in thread: Do you lose carb if you warm up keg? on 05-22-2014 at 05:37 PM
    the head pressure will increase inside the keg, but so long as its sealed, that extra escaped
    gas will reenter the beer when it gets chilled again, so, no lost gas (unless you have a leak;
    remember th...

  • Posted in thread: Whirlpool Direction on 05-22-2014 at 05:34 PM
    It's an interesting conclusion. Don't know if it really matters for homebrewers, but I'm still
    curious about what they did and how they measured.I wasnt able to find it either, but the only
    force that...

  • Posted in thread: DS18B20 used on a RIMS with Arduino PID Library on 04-30-2014 at 08:38 PM
    so I'd assume from that they are very accurate. just keep in mind the difference between
    accuracy and precisionthree probes reading similar readings should lead you to believe that
    they are *precise*....

Following Stats
November 3, 2014  •  06:19 PM
Hi there, what false bottom do you use to recirculate mash? I have a RIMS tube setup but yesterday when I brewed the flow was too low, because of the compacted grain bed.

When I use a BIAB the bag got stucked and clogged the pump.