VIEW MY

AndrewT

Gift Premium Subscription To AndrewT

Join Date:

02-06-2011

Last Activity:

02-09-2014 9:04 PM

1 Likes on 1 Posts 

    ABOUT ME

  • IPA,
    American Wheat,
    CAP,
  • Breakfast Stout,
    Cream Ale,
    American Wheat,
    Dunkelwizen
  • Moose Drool Clone,
    Barley Wine
  • Male
  • Married
  • Carson
  • IA

LATEST ACTIVITY

  • Posted in thread: Anyone haerd of these new Yeasts from Mangrove Jack's (New Zealand) on 04-23-2013 at 01:18 AM
    Which shop in Omaha?I would be willing to give some a try.I could split between a couple of 3
    gal fermenters and ferment at different temps.Andrew

  • Posted in thread: Omaha bulk grain purchase on 04-15-2013 at 09:04 PM
    There was one just a couple weeks ago. I think the order is closed now, haven't received the
    grain yet. Send me your info and I can try to get you in on the next one.PM sent.Thanks!

  • Posted in thread: Omaha bulk grain purchase on 04-11-2013 at 03:08 PM
    Any idea as to when the next bulk buy will be happening?Andrew

  • Posted in thread: Jockey Box Cold Plate Question on 04-06-2013 at 12:47 PM
    My cold plate uses the 1/4mfl X 3/8 mfl.Make sure to uses the plastic seals on both sides or
    end up with beer in the jockey box.Cheers!

  • Posted in thread: 10 gallon cooler SS False Bottom Round Up on 04-06-2013 at 12:35 PM
    Here's what I'm currently using from Adventures in Homebrewing.I was previously using a
    standard perforated false bottom but ended up with a lot of stuck mashes.I decided to use this
    FB after reading ...

  • Posted in thread: Leftover grains on 04-05-2013 at 01:46 AM
    Check out ritebrew.com. They sell by the ounce or the pound.You also get a discount when buying
    more than 10lbs of the same grain.You can setup grain bills so that all the grains for your
    brew can be ...

  • Posted in thread: Can I salvage this manifold? on 03-30-2013 at 01:14 AM
    What gas fittings did you buy from Ritebrew?Looking at their website, only the regulator has a
    3/8" barb.They state that 5/16" tubing will fit over the barb or you can swap out the input on
    the manifo...

  • Posted in thread: Controlling flow...alternatives to long lines or swizzle sticks on 03-24-2013 at 02:29 PM
    In soda dispensing setups, they use an 1/8 id hose connected to 3/16 MFLs.If you can find the
    smaller id tubing, you would be able to shorten the run.I'm currently out of town but will post
    a picture ...

  • Posted in thread: Wiring Switch help on 03-23-2013 at 04:32 PM
    You are correct.Green is NO & Red in NC?The gray block is the connection for the led.The
    auction listing is for a 24v AC/DC supply for the led.Do you plan on switching a transformer on
    and off with wh...

  • Posted in thread: SSR latching? on 03-17-2013 at 05:03 AM
    I have this same issue with my HLT. I have tried several SSRs. They all do this as well. Mine
    are rated for 60 amps and is controlling 5500w element. I have to cycle the power to get them
    to release. ...

0 COMMENTS
POST A COMMENT

Newest Threads

LATEST SPONSOR DEALS