Stealthcruiser

Gift Premium Subscription To Stealthcruiser

Join Date:

05-07-2013

Last Activity:

01-28-2015 7:49 PM

Age:

58 years old

Birthday:

5/31/1956

Likes Given: 2502

167 Likes on 150 Posts 

    ABOUT ME

  • Aviation Maintenance.Aircraft sheet metal fabricator.
  • A M T
  • South Atlanta Homebrewers Association.
  • Male
  • Married
  • Atlanta, (Hampton).
  • Georgia

LATEST ACTIVITY

  • Posted in thread: Mineral Oil as Hose Lube? on 01-29-2015 at 01:49 AM
    You could use a little K-Y jelly.Water soluble.Some folks use a "little" keg lube.And, as
    mentioned, make yourself a "smooth barb" fitting.

  • Posted in thread: Blow off tube set ups on 01-29-2015 at 01:10 AM
    Here's a couple: big , reinforced vinyl hose like Home Depot carries, happens to be 1 3/8
    O.D., which corresponds to the opening in "most" glass carboy's.It's a tight fit, with a short
    chunk lubed up...

  • Posted in thread: Tri-Clamp Sight Glass - will it shatter? on 01-28-2015 at 11:37 PM
    Hmmmm........How long a period, before the boiling wort gets switched over to "chilled" wort?I
    ask,' cause if it's a few minutes, ( re: sight glass is tolerable to your touch), I doubt
    you'll have pro...

  • Posted in thread: Getting a heat source inside my fridge on 01-28-2015 at 09:49 PM
    Make the existing hole bigger........Probe around in the cabinet / insulation jacket looking
    for wires and refrigerant coils.Nothing noted?Open it up slightly, so your plug will fit
    through.I would su...

  • Posted in thread: Is my Mash Tun too big? on 01-28-2015 at 09:26 PM
    ...but first do a search about insulating lids with expanding foam. Some have shown that it
    doesn't work well because it never really expands.^^^^^^ This!The "Great Stuff" in a spray
    can,needs contact...

  • Posted in thread: Monster Mill Hopper doesn't seem to fit on 01-28-2015 at 08:09 PM
    "Fred", (I'll withhold last name), Is Fred at Monster Brewing, that makes the Monster Mill, and
    he's in our brew club.Heel of a nice guy, and I was thinkin' that you may have purchased it
    through Mons...

  • Posted in thread: HBer with Plasma Cutter Near ATL? on 01-28-2015 at 05:08 PM
    I've seen some damn fine skills, with a plasma and a cutting torch, that I could only aspire to
    emulate!

  • Posted in thread: HBer with Plasma Cutter Near ATL? on 01-28-2015 at 01:34 AM
    Got it cut yet?No plasma cutter, but I have a nice fixture for cutting keg tops out, using a
    high speed grinder, and I like milk stouts....... on the South Side, in Hampton, Ga.,( like it
    says under ...

  • Posted in thread: #10 stopper with hole for thermowell-where to find on 01-28-2015 at 12:49 AM
    They drill pretty good too, after a dunk in liquid Nitrogen..........:)

  • Posted in thread: Big Mouth Bubblers are dangerously thin on 01-28-2015 at 12:33 AM
    :) I have to ask why?If I think someone is going to get hurt by something then I say take it
    out of commission entirely, not hand it off to someone else.That, or hand it off to someone in
    Raleigh!.......

Following Stats
FORUM SIGNATURE
Corned Beef............The other pink meat.
0 COMMENTS
POST A COMMENT

Newest Threads

LATEST SPONSOR DEALS