Spine

Gift Premium Subscription To Spine

Join Date:

07-04-2008

Last Activity:

07-22-2012 8:04 AM

    ABOUT ME

  • Guelph, ON, CANADA
  • Systems Engineer
  • Mike
  • AG /w 48qt Cooler MLT, Batch Sparge, Steam Mashing, SLC 5/03 Lagerator, Keg System
  • Irish Cream Ale, Newcastle Brown Clone, Belgian Wit, Bavarian Hefeweizen, Munich Helles, Maerzen, Edwort Haus Pale Ale
  • Male
  • In a Relationship

LATEST ACTIVITY

  • Posted in thread: "Buzz" in element or ssr on 06-08-2010 at 02:35 AM
    Don't worry!I have an electric keggle and electric HLT (both 4500w) and depending on the amount
    of water and the temperature, they will both start to "howl" but this usually only lasts until
    the water...

  • Posted in thread: Brewing Books for Sale! on 05-14-2010 at 10:03 PM
    Hello All,I need to generate some cash in order to upgrade some of my equipment so I am selling
    some brewing books.1. The Home Brewers Companion - Charlie Papazian2. New Brewing Lager Beer -
    Gregory J...

  • Posted in thread: Mike's E-KEGGLE on 03-23-2010 at 01:54 AM
    Hey Brewing Clamper, Sorry for the delay in replying. I have been very busy with work lately
    and haven't been doing any brewing, let alone logging into this board.Yes you are correct, I
    did change the...

  • Posted in thread: Arduino with 2wire/SMBUS digital thermometer on 12-30-2009 at 03:01 PM
    uhhh help anyone?... got 4 wires going into the ds1624... connected the sda and scl of the
    ds1624 to the sda and scl of the arduino.. tried spines code and am only reading "0.00"'s on
    the serial port ...

  • Posted in thread: Arduino with 2wire/SMBUS digital thermometer on 12-30-2009 at 02:46 PM
    My feeble mind is a bit puzzled. What does resolution mean in relationship to accuracy, and why
    is it important if the accuracy is the same?I might have said it the wrong way, but essentially
    the one ...

  • Posted in thread: Siphon inside keggle doesn't work on 07-14-2009 at 12:42 AM
    I had the same issue with my keggle as well. I ended up silver soldering a 3/4" FPT to 1/2"
    solder fitting to the bottom of the keggle and then drilling out the hole after it was
    soldered. It was the ...

  • Posted in thread: Adjustment Without Salts on 07-10-2009 at 01:13 AM
    I have a home water distiller, nice one, 3 or 4 gallon tank, auto refill or manual fill. 10
    bones in a second hand shop.; just needed the spigot nut tightened inside the tank. Not RO, but
    I am guessin...

  • Posted in thread: Adjustment Without Salts on 06-30-2009 at 08:46 PM
    I have similar water to what you have except my other minerals are a tad higher but my
    alkalinity is around 347ppm. I found that by diluting the mash and sparge water to 75%
    distilled/25% tap water an...

  • Posted in thread: Mike's Electric Indoor Brewhouse on 05-29-2009 at 09:32 PM
    Agreed, nice write-up. I also like the idea of the bottom drainI have a question - not sure if
    it is appropriate for this thread but didn't think it was worth starting a new one.I'm planning
    to go ele...

  • Posted in thread: Mike's Electric Indoor Brewhouse on 05-27-2009 at 12:57 AM
    Thanks for the hints - I already had the Arduino and the LCD screen was only $12 USD off e-bay
    and I had the temperature probes left over from school so the control system really didn't cost
    me that m...

Following Stats
0 COMMENTS
POST A COMMENT