Spike Brewing 12.5 Conical Fermenter Giveaway!

Home Brew Forums > Home Brewing Beer > DIY Projects > valves/fittings ordered, hole directions needed..

Reply
 
LinkBack Thread Tools
Old 02-02-2011, 08:12 PM   #1
krenshaw
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
krenshaw's Avatar
Recipes 
 
Join Date: Dec 2010
Location: Lancaster, PA
Posts: 1,086
Liked 48 Times on 44 Posts
Likes Given: 27

Default valves/fittings ordered, hole directions needed..

i have my 2 kegs cut open from the top, and waiting for my shipments from bobby and bargainfittings to continue.. in the meantime i was wondering about location of the fittings to be drilled/welded into my BK and HLK..

i've noticed a lot of talk about where from the bottom up to put holes, as to make it as low as possible but still flush and not on the curved part, but i haven't found much about the location with regards to which part of the keg..

i saw pics of people that have their valves located directly below the handle of the keg toward the bottom, which makes me think it may be easier to pick up from the sides of your brew rig..

i've also seen some that have them installed almost at a 45 degree angle on the side with the thermometer and sighttube more in the middle, my guess is it would be less of a bend in your tubing to transfer from one vessel to the next (whether using a pump or not)

any discussion on what you all do, or is it more of a valve in the bottom middle, thermometer slightly above that, and tube (if you have one) to the left or right a bit? i also remember recently reading a thread where somebody mentioned it is better for nothing to be located to the left of the valve (when looking at the keg) but i can't remember why..

__________________

~ A fine beer may be judged with only one sip, but it's better to be thoroughly sure.

DOWN THE HATCH BREWING
Stainless Hop Spider | Wooden Brew Rig | Dual Hinge Keezer Build

Primaries.. oxy :-(
Keg 1: Apfelwein | Keg 2: BlackEyePA version2 | Keg 3: Summer Saison
Bottles: lots full and even more empty

krenshaw is offline
 
Reply With Quote Quick reply to this message
Old 02-02-2011, 08:46 PM   #2
MW66
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
MW66's Avatar
Recipes 
 
Join Date: Mar 2010
Location: Buffalo, NY
Posts: 267
Liked 10 Times on 10 Posts

Default

As low as possible, but still on the flat surface. I have my valve mounted right between the two handles and in the middle of two of the vent holes on the bottom, so it's away from the flame. I mounted my thermo/sight glass on the next section over from the valve, but about the same height. The lowest reading I can get from my sight tube is 4 gallons.

http://www.homebrewtalk.com/f51/belgian-horse-221075/

__________________
MW66 is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
ASCO valves vs. furnace valves Eigenbrau DIY Projects 5 07-31-2010 08:00 AM
Tap Tower - New Hole jtrainer DIY Projects 6 10-09-2009 12:34 AM
Directions for kegerator fan box? SevenFields DIY Projects 1 10-01-2009 12:39 AM
Gas Valves Buzzy DIY Projects 3 12-04-2008 02:37 AM
Gas Valves pluto DIY Projects 0 03-06-2008 05:13 PM