New Giveaway - Wort Monster Conical Fermenter!

Home Brew Forums > Home Brewing Beer > DIY Projects > Secondary regulator issues




Reply
 
LinkBack Thread Tools Display Modes
Old 02-28-2012, 12:35 PM   #1
inhifistereo
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: Madison, WI
Posts: 56
Default Secondary regulator issues

I purchased a Haeir kegerator off of craigslist a few weeks ago complete with 5 lb CO2 tank. I wanted to add a few more kegs to my setup so I purchased a secondary regulator from Micromatic along with a 3-tap tower. I installed the secondary regulator with approximately 2.5 feet of hose between the primary and secondary regulator. Then ran 5 feet of gas hose from each secondary connection.



Last night I set the primary regulator psi to 21.



Then set each secondary to 10 psi. This morning I woke up and my primary is holding rock solid at 21 but my secondaries have all fallen way below 10 psi.



What is my issue here? Is it because the secondary regulator is laying down? Is 5 feet too much hose to my gas-in post? Or is it because I don't have a keg hooked up yet?

I would assume that if the secondary's pressure fell that the primary would as well. Wrong assumption?



__________________

Friends don't let friends go to grad school...

inhifistereo is offline
 
Reply With Quote Quick reply to this message
Old 02-28-2012, 06:38 PM   #2
david_42
Feedback Score: 0 reviews
 
david_42's Avatar
Recipes 
 
Join Date: Oct 2005
Location: Willamina & Oak Grove, Oregon, USA
Posts: 25,650
Liked 130 Times on 124 Posts

Default

Yes, wrong assumption. The pressure in the primary is independent of the secondaries. I suspect the pressure loss is just due to a temperature change. Also, new regulators can take 2-3 adjustments to stabilize.



__________________

Remember one unassailable statistic, as explained by the late, great George Carlin: "Just think of how stupid the average person is, and then realize half of them are even stupider!"

"I would like to die on Mars, just not on impact." Elon Musk

david_42 is offline
 
Reply With Quote Quick reply to this message
Old 02-28-2012, 06:47 PM   #3
inhifistereo
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: Madison, WI
Posts: 56
Default

The kegerator isn't even turned on yet. I just want to get a baseline.

I turned up the primary to 40 psi and set the secondaries to 10 psi. Once everything was pressurized I shut off the tank and the primary regulator feed. I let it sit and after approximately an hour I noticed that the first secondary regulator had fallen down to 6 psi. Now I just need to pinpoint where the leak is in that regulator.

__________________

Friends don't let friends go to grad school...

inhifistereo is offline
 
Reply With Quote Quick reply to this message
Old 02-28-2012, 09:22 PM   #4
bucfanmike
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
bucfanmike's Avatar
Recipes 
 
Join Date: Apr 2010
Location: Duluth
Posts: 1,011
Liked 20 Times on 19 Posts
Likes Given: 3

Default

you just wont get accurate readings without having somewhere for the gas to go. Take one of you quick disconnects and manually push the gas pin in the center and watch the needle will probably move up near the 10 again. There is a good chance that you may have a slow leak on the reg that is down to 0.

__________________

Mike in Duluth

Currently on Tap
1. Hefeweizen
2. BM Centennial Blonde
3. LHMS Clone

Pipeline
Next on Tap-Denny Conn Rye IPA
Kegged and aging Ed Worts Apfelwine, Denny Conn BVIP
Fermenters -

bucfanmike is offline
 
Reply With Quote Quick reply to this message
Old 02-28-2012, 10:49 PM   #5
krazydave
Feedback Score: 1 reviews
Recipes 
 
Join Date: Aug 2010
Location: Santa Clarita, California
Posts: 847
Liked 23 Times on 21 Posts
Likes Given: 3

Default

I think you need to hook the lines up to something. The small amount of space in the lines probably isn't enough for the regulator to actually regulate anything.

BTW, if you suspect you have a leak, a strong star-san mix and a spray bottle works wonders.

And like someone else already said, it sometimes does take a few adjustments to get the pressure to stabilize where you want it.

Fear not, when you have kegs hooked up, all will likely be just fine.

__________________
krazydave is offline
 
Reply With Quote Quick reply to this message
Old 02-29-2012, 01:47 AM   #6
thargrav
Registered User
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Location: Huntsville, Alabama
Posts: 821
Liked 38 Times on 35 Posts
Likes Given: 2

Default

You need to ask Micromatic what differential pressure these regulators need to operate correctly. Your differential is 11 PSI now (21 PSI - 10 PSI) and I bet these are designed to operate with a differential of at least 11 PSI & possibly 30 PSI or higher.

Or better yet, just crank your primary up to 40 PSI. If your secondary pressures move up than that's exactly what's going on.

__________________
thargrav is offline
 
Reply With Quote Quick reply to this message
Old 02-29-2012, 12:50 PM   #7
inhifistereo
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: Madison, WI
Posts: 56
Default

So I turned the primary up to 40 psi and purged the line by pushing in the pin at the bottom of the quick disconnect. My secondaries shot right up to 10 psi and held. I left everything overnight and when I got up this morning to check, sure enough the first regulator had dropped to almost nothing. I ordered some Gas Leak Check from Northerbewer that should hopefully be here this afternoon. Worst case scenario I just take all the Gas Shut off valves off again, reapply teflon tape, and then reinstall them again.

__________________

Friends don't let friends go to grad school...

inhifistereo is offline
 
Reply With Quote Quick reply to this message
Old 03-01-2012, 01:41 PM   #8
inhifistereo
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2008
Location: Madison, WI
Posts: 56
Default

So another day, another test. The secondaries held 10 psi for a good 9 hours yesterday. When I awoke this morning we were down to nothing again. I called my keg supply contact again and we determined (via krazydave's advice) that until we get a keg hooked up the gas is most likely leaking from the coupler. Couplers are meant to feed gas, not stop it from leaking, that's what the keg's seals are for. So we'll know more in about a week once we get the keg hooked up.

__________________

Friends don't let friends go to grad school...

inhifistereo is offline
 
Reply With Quote Quick reply to this message
Old 03-01-2012, 02:04 PM   #9
Thirteen
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
Thirteen's Avatar
Recipes 
 
Join Date: Jan 2010
Location: Bowmanville ON
Posts: 129
Liked 1 Times on 1 Posts

Default

The coupler is meant to do both actually. If it won't hold pressure then it is defective in some manner.

__________________
Thirteen is offline
 
Reply With Quote Quick reply to this message
Old 03-01-2012, 03:19 PM   #10
starsailor
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2008
Location: Central MA
Posts: 278
Liked 10 Times on 10 Posts
Likes Given: 1

Default

My first thought on your problem was the pressure differential between the primary and the secondaries, but it seems like you've eliminated that, assuming you did find out what the required input pressure is for the secondaries to function properly. That aside, the secondary regulators are designed to hold a constant ouput pressure as long as there is sufficient pressure and flow on the inputs. The volume of gas space being controled on the output side shouldn't matter, meaning the just the line and disconnnect should be connected to a keg or not. If one or more of the secondaries won't flow gas to maintain the set pressure on the output side either:

1. Gas is leaking out of the keg line faster than the regulator can flow. This is likely not the case as you'd probably hear it and tank isn't empty yet.

2. The seconary(s) input is blocked. This isn't likely the case as you can initially get the secondary(s) up to the set output pressure without any problem. Although you could have created a blockage if you got some pipe dope sealant or teflon tape into the secondary(s) input when assembling the system. I've gotten teflon tape in a couple of things this way by wrapping the tape past the end of the threads on a connectionby mistake even without covering the opening because the threads can cut the tape when screwed together. I now make sure I never wrap teflon tape too far down the male parts to prevent this.

3. The secondary(s) diaphram is sticking or the spring is defective. I'd suggest that this is the most likely problem. It could have been caused if you somehow had beer in the primary output line before you hooked it up to the secondary(s). You could easily have never noticed it because you have opaque red gas line on your primary output. I always use clear braided hose just so I can see what's in there. Beer injected into the output of a new secondary could easily cause the diaphram to get sticky and not function properly especially as a low pressure differential may not produce enough force to overcome any stickyness. The first secondary inline showing a lower pressure the the others supports this because any beer would likely go into the first secondary when it assemble system was first pressurized. Depressing the keg connector pin to discharge gas also support this because it creates a larger pressure across the secondary diaphram of that regulator. I'd try to jack up the primary output pressure to the max of secondary input pressure or the limit of your hoses and see if it gets any better. If so, disassemble the first secondary and see if the diapharm has gunk on it and if so clean and reassemble. During disassembly you'll also get to see if there's any tape ect. causing a blockage. If jacking up the primary output pressure doesn't help at all or if the first secondary diapharm is clean and nothing is plugging in up then I'd return the regulators as defective because you can't fix a bad spring or anything else.



__________________
On Tap: Apfelwein, SkeeterPee
Bottled: Robust Porter, Roasty Toasty Stout, Belgian Wit, Belgian Saison
Kegged: None
Primary: Rye-I-Brew Belgian Rye Saison
Secondary: None
On Deck: Wheat ale
RIP: BadBoy Wit, Wild Cider, Got Mild?x2, Wyeast Cider-2x, SO4 Cider, Wheat ale, Carnival Kölsch-2x, Am Pale Ale, Am Brown Ale, Dunkel Larger, Erik The Red, Newporter, Cream Ale, Bitter, Trapist Triple, Bourbon Oaked Porter, Gluteus Minimus(Gluten Free)-2x, English Brown

Wizards Homebrew Club
starsailor is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Homemade secondary regulator smurfwar DIY Projects 13 02-17-2012 02:16 AM
Build secondary regulator? marms DIY Projects 7 11-04-2011 11:10 PM
Secondary Regulator Orientation XPLSV DIY Projects 2 08-14-2011 08:26 PM
Issues after adding secondary regulator.. sirhcman DIY Projects 8 01-13-2011 02:28 AM
Regulator issues Matovichi DIY Projects 3 08-20-2008 04:26 AM