Home Brew Forums

Home Brew Forums (http://www.homebrewtalk.com/forum.php)
-   DIY Projects (http://www.homebrewtalk.com/f51/)
-   -   RIMS VS HERMS, what if? (http://www.homebrewtalk.com/f51/rims-vs-herms-what-if-103320/)

bplaughlin 02-13-2009 11:45 PM

RIMS VS HERMS, what if?
 
I have been considering uping my brew stand to a RIMS or a HERMS system.

Here is what I am thinking instead. Taking coiled copper, much like a wort

chiller, and installing it into my mash tun. Than pumping hot water from my HLT

through it. For example, when i go to mash out I would heat my water to 170

and pump it through the copper in the mash tun until the temp is reached.

This would alaw the heat exchange to take place right in the mash tun without

the temperature ever exceeding the target temp. It would also keep only

clean water runing through my lines makeing them easier to keep clean and

maintain. What do you think?

GilaMinumBeer 02-14-2009 12:02 AM

So, you are talking about having your HERMS coil in the mash?

That just sounds like a PITA to keep clean.

More so than running the wort through the coil because, IIRC, most HERMS brewers run their sparge water through their coil to collect the wort from inside it. Tah Dah! Clean, inside and out.

bplaughlin 02-14-2009 12:16 AM

I see your point about cleaning but i wouldn't think it would be different then getting leaf

hops off a wort chiller. I just put mine in some water with vinegar in it to clean than give

it a good rinse with clean water or lefter over sanitizer.

Joe Camel 02-14-2009 01:35 AM

If you installed the coils in your mash tun to heat the mash, you would still need to stir the mash to ensure even heating. Constant stirring of the mash is a PITA

If you install the coils in your hlt and recirc the mash with a pump, this is taken care of by the pump.

BrewBeemer 02-14-2009 01:58 AM

Quote:

Originally Posted by bplaughlin (Post 1132611)
I have been considering uping my brew stand to a RIMS or a HERMS system.

Here is what I am thinking instead. Taking coiled copper, much like a wort

chiller, and installing it into my mash tun. Than pumping hot water from my HLT

through it. For example, when i go to mash out I would heat my water to 170

and pump it through the copper in the mash tun until the temp is reached.

This would alaw the heat exchange to take place right in the mash tun without

the temperature ever exceeding the target temp. It would also keep only

clean water runing through my lines makeing them easier to keep clean and

maintain. What do you think?


You can not reinvent the wheel unless in your situation you are bored and insist on making your brew day more difficult than is necessary. Cleaning it what a PITA but again don't knock another persons brew system if they are happy with it.

bplaughlin 02-14-2009 01:59 AM

I was thinking about that and started to consider an electric stir (ya i know its more work but i have tinker). Now, wouldn't you have to stir the mash

anyway or does the constent flow of the wort enough to get even heat distribution?

The Pol 02-14-2009 02:08 AM

If you are pumping and heating water, it makes more sense to use a typical HERMS coil. Pump the mash, not the wter. There is no real cleaning to a HERMS coil... simply pump your sparge water through it, that will clean it out almost completely.

If you place a coil in the MASH and run hot water through it... how will you stir the mash?

Where will your temp probe go?

There is less equipment and hassle involved in running a typical HERMS. They are very simple, efficient and do not require stirring the mash.

ONE benefit to a HERMS or RIMS is that you have SUPER clear wort since you are recirculating it for an hour. Your proposed method would not give you this benefit.

bplaughlin 02-14-2009 02:15 AM

I'm seeing the point to a traditional HERMS. Thanks for kicking around the idea

with me, it help me to focus my creativity.

bplaughlin 02-14-2009 02:56 AM

OK, this may seem like an obvious question but how do you run sparge water through the coil. Are

you running freshwater thought it using the HLT to heat it or are you running the

existing water in the HLT through it. I'm thinking of using the heated water of the HLT

through it by using a disconnect on one end with a hose that would run down to the

bottom. The pump would obviously have to run from the HLT to the MT.

Superman3278 02-14-2009 03:11 AM

Here is what kills me about a HERMS, no stiring! It does every thing a comercial tank does ecept stir, wich increases the efficiancy. Seems to me the wheel does need upgading period. AB gets 95 % because of stirin rakes, gaps are greated to help wash the grains, thusly get on with your project how you see fit and happy brewing. I would like to think efficiancy is no. 1 in all grain esle why bother.


All times are GMT. The time now is 06:57 PM.

Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.