Kegconnection Complete Starter Kit and More Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Question for grain mill hopper build

Reply
 
LinkBack Thread Tools
Old 05-11-2012, 12:28 PM   #1
Kmcogar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Dunkirk, Maryland
Posts: 975
Liked 29 Times on 21 Posts
Likes Given: 3

Default Question for grain mill hopper build

Just received my crank and stein 2s (4 inch rollers) I am going to be building my hopper when I get off work today. I got my general design. My question is, how big should the hole be that feeds the grain to the mill? My friends mill looks to be about 8 inch rollers but there is only a 2 inch opening. Is that fine? Or can I get more grain crushed with a bigger hole? Or can that jam up my mill rollers?



Here's a picture of his.



image-3383273709.jpg



image-2021981737.jpg

__________________

Ægir was a god who would host a party where all the gods would drink the beer he brewed for them. He made this in a giant kettle that Thor had brought. The cups in Ægir's hall were always full, magically refilling themselves when emptied.

Kmcogar is offline
 
Reply With Quote Quick reply to this message
Old 05-11-2012, 03:13 PM   #2
magno
Feedback Score: 0 reviews
 
magno's Avatar
Recipes 
 
Join Date: Feb 2006
Location: Austin, TX
Posts: 909
Liked 5 Times on 4 Posts

Default

My hopper runs nearly the entire length of the rollers. Jamming is not an issue.

__________________
Planning: New brewery at new house!!

Primary: Barley Wine

Secondary: Red Ale, Pale Ale

Conditioning:

Drinking: Brown Ale, 75 min. IPA, Oatmeal Stout, Poor Richard's Ale, Chocolate Cherry Stout
magno is offline
 
Reply With Quote Quick reply to this message
Old 05-11-2012, 06:34 PM   #3
rico567
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
rico567's Avatar
Recipes 
 
Join Date: Apr 2008
Location: Central IL
Posts: 3,018
Liked 82 Times on 77 Posts
Likes Given: 21

Default

Yeah....if the width of the opening is 8 inches, why would the aperture admitting the grain to the rollers be less? If jamming is an issue, it needs to be addressed separately from this question. Probably with more torque.

__________________

“Malt does more than Milton can / To justify God’s ways to man”

-A. E. Housman (1859–1936). A Shropshire Lad , 1896.

rico567 is offline
 
Reply With Quote Quick reply to this message
Old 05-11-2012, 07:22 PM   #4
DustyTheBrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2011
Location: Belleville, Ontario
Posts: 103
Liked 1 Times on 1 Posts
Likes Given: 7

Default

Mine runs almost the whole length as well with no issues. Here is a pic of my crude plywood hopper (although you can't see the inside).

__________________
www.dustysbrew.com
DustyTheBrewer is offline
 
Reply With Quote Quick reply to this message
Old 05-11-2012, 07:50 PM   #5
Kmcogar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Dunkirk, Maryland
Posts: 975
Liked 29 Times on 21 Posts
Likes Given: 3

Default

Quote:
Originally Posted by DustyTheBrewer
Mine runs almost the whole length as well with no issues. Here is a pic of my crude plywood hopper (although you can't see the inside).
I think I'm gonna make mine just like yours dusty. How tall is yours? And how much grain does it hold?
__________________

Ægir was a god who would host a party where all the gods would drink the beer he brewed for them. He made this in a giant kettle that Thor had brought. The cups in Ægir's hall were always full, magically refilling themselves when emptied.

Kmcogar is offline
 
Reply With Quote Quick reply to this message
Old 05-11-2012, 09:52 PM   #6
Chrisl77
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2011
Location: Jackson, New Jersey
Posts: 693
Liked 31 Times on 29 Posts
Likes Given: 1

Default

I took a piece of light gauge sheet metal and made a shield to go over the top of the rollers to direct the the grains to the center. I cut a slit in the center just a little shorter then the rollers and a cross slit at each end, then i bent the two tabs inwards towards the rollers a little. This keeps the grains from going around the rollers instead of through the middle of them.

__________________
Ocean County home brew club
Chrisl77 is offline
 
Reply With Quote Quick reply to this message
Old 05-14-2012, 12:24 PM   #7
Kmcogar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Dunkirk, Maryland
Posts: 975
Liked 29 Times on 21 Posts
Likes Given: 3

Default

Quote:
Originally Posted by Chrisl77
I took a piece of light gauge sheet metal and made a shield to go over the top of the rollers to direct the the grains to the center. I cut a slit in the center just a little shorter then the rollers and a cross slit at each end, then i bent the two tabs inwards towards the rollers a little. This keeps the grains from going around the rollers instead of through the middle of them.
Looks good
__________________

Ægir was a god who would host a party where all the gods would drink the beer he brewed for them. He made this in a giant kettle that Thor had brought. The cups in Ægir's hall were always full, magically refilling themselves when emptied.

Kmcogar is offline
 
Reply With Quote Quick reply to this message
Old 05-14-2012, 12:31 PM   #8
Kmcogar
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2011
Location: Dunkirk, Maryland
Posts: 975
Liked 29 Times on 21 Posts
Likes Given: 3

Default

This is what I ended up doing. It worked out pretty well. Definitely not as pretty as I hoped it to be but it gets the job done. It holds about 5lbs of grains. It's crushed the 5lbs in about a minute. SWEEEET!!!



image-49976101.jpg



image-992726239.jpg



image-16932948.jpg

__________________

Ægir was a god who would host a party where all the gods would drink the beer he brewed for them. He made this in a giant kettle that Thor had brought. The cups in Ægir's hall were always full, magically refilling themselves when emptied.

Kmcogar is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools




Newest Threads