Electric Brewing Supply 30A BCS Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > My Kegerator Build
Reply
 
LinkBack Thread Tools
Old 05-06-2010, 02:44 AM   #1
Chris1272
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: Auburn, AL
Posts: 213
Liked 3 Times on 2 Posts

Default My Kegerator Build

I thought I would share my first real DIY project with you guys.

I started with a Danby 4.4 cu. ft. refrigerator. Purchased from Wal Mart.


I removed the plastic door piece, and had a piece of plywood cut to the same dimensions. after spray painting it white I replaced the rubber boarder and installed it in the door.


Here I'm using a hole saw to drill through the top of the unit for the tubing. It is very slow going when cutting through the metal top.


The two Cornelius kegs and CO2 canister and manifold that will be going in the fridge.


Measure twice cut once and drink home brew while your work... I think thats how it goes. anyway Im making measurements and reference points to center the tap tower.


Here is a top down view. with waterproof tape lining the hole to keep moisture out of the exposed insulation.



Im making marks for drilling pilot holes for securing the tap.


Here I am tightening the bolts from up under. I found out you need longer bolts than what come with the tap so this is right after an unplanned midnight run to wally world for some 2 1/2 in #10 bolts and washers.


here it is all done with kegs tucked away in their new home.


The first test pour of warm flat beer... Tastes like success.


It was a lot of fun and certainly wont be my last project.

__________________

Chris1272 is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 02:50 AM   #2
calebawilson
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Katy, tx
Posts: 212
Liked 1 Times on 1 Posts
Likes Given: 4

Default

that looks awesome. got to build me one.

__________________
calebawilson is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 05:52 AM   #3
Mustangj
Feedback Score: 0 reviews
 
Mustangj's Avatar
Recipes 
 
Join Date: Oct 2006
Location: Dublin, Oh
Posts: 1,439
Liked 2 Times on 2 Posts
Likes Given: 17

Default

I like it!

__________________
"If my mother was tied up and held ransom, I might think about making a light beer."Greg Koch
Stone Brewing

Michigan Mashers
http://www.homebrewtalk.com/groups/michigan-mashers/
Mustangj is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 06:13 AM   #4
CDbrews
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2009
Location: MN
Posts: 344
Liked 2 Times on 2 Posts
Likes Given: 1

Default

did you have to modify this fridge at all?

__________________

_________________
Primary1: Strawberry Blonde
Primary2: Kiwi Blonde
Sanke Primary: Oxyclean
Bottled: Imperial Stout
Kegged: Centenial Pale Ale, Peat Malt Porter, Rye Pale Ale, Maibock
Near Future: Red Ale, Kolsch

CDbrews is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 06:17 AM   #5
kegtoe
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
kegtoe's Avatar
Recipes 
 
Join Date: Sep 2009
Location: I Fall MN
Posts: 1,326
Liked 13 Times on 12 Posts
Likes Given: 10

Default

how where you sure not to hit the cooling elements??

kegtoe is online now
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 11:52 AM   #6
Chris1272
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: Auburn, AL
Posts: 213
Liked 3 Times on 2 Posts

Default

Quote:
Originally Posted by CDbrews View Post
did you have to modify this fridge at all?
The only modification I did was remove the door panel that holds cans and things and add the plywood replacement. other than that a 5lb co2 tank sits nicely in the back with 2 corny kegs.


Quote:
Originally Posted by kegtoe View Post
how where you sure not to hit the cooling elements??
Before starting I did a little research, this model only has one cooling line that runs across the top of the unit and it is near the front right behind the door. the only thing that is an issue is the wiring for the light and thermostat. I called danby tech support before drilling and asked if they have any lines that run in that area. The guy told me there are wires that power the thermostat and the light for the unit. during manufacture these wires are installed and the foam insulation is injected so there inst a guarantee they wont be where you want to drill. I didn't run into this problem but after broke through the metal I went very slowly by hand through the foam. If you look where the wires are heading going into the unit from the thermostat to where the cord is installed on the bottom of the unit its doubtful that you will encounter any electrical wiring.


My next project may be to cut the wire that goes to the light in the top and use it to power a fan to blow air into the tower.
__________________
Chris1272 is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 12:44 PM   #7
fatherbigfoot
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Lansing Mi
Posts: 178
Liked 3 Times on 3 Posts

Default

did you use and support for your bolts that hold the tower in place I have seen people that instal a piece of plywood inside the fridge to support the tower? is this the DAR482 model?

__________________
fatherbigfoot is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 02:33 PM   #8
Chris1272
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: Auburn, AL
Posts: 213
Liked 3 Times on 2 Posts

Default

Quote:
Originally Posted by fatherbigfoot View Post
did you use and support for your bolts that hold the tower in place I have seen people that instal a piece of plywood inside the fridge to support the tower? is this the DAR482 model?
My model is the Danby 440BL I have seen the builds you are talking about with the DAR482. As far as I can tell they are very similar units my model did not have the wine rack shelf or the vegetable crisper, and the shelving in the door was different. Since you are going to pull it all out anyway I don't think it makes much of a difference. as for the support I had one that I cut out of the spare plywood I used for the door, but when I installed the Tower I found that with some locking washers between the plastic and the bolt that it is secured pretty firmly. That being said the only torque on that mount should be the pulling of the tap handles if you foresee someone leaning on your tower or it being bumped a lot the extra support may be warranted.
__________________
Chris1272 is offline
 
Reply With Quote Quick reply to this message
Old 05-06-2010, 11:21 PM   #9
whale
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: BC
Posts: 58
Liked 1 Times on 1 Posts

Default

I've done a same project. this fridge has no freezer, no cooling element to deal with and it fit two corny. I have a 20# co2, I had to cut a small hole to run a line in. it took me about 2hours to convert it.

__________________
whale is offline
 
Reply With Quote Quick reply to this message
Old 06-19-2010, 09:02 PM   #10
MissouriBrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2010
Location: St. Louis, MO
Posts: 16
Default

Any idea if you could use this fridge for a double tap door mounted system? I need to get this under my countertop and don't want to drill through the top.

__________________
MissouriBrewer is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Kegerator build Myrdhyn DIY Projects 21 09-07-2010 12:49 AM
Sure, you can build a kegerator.. aekdbbop Bottling/Kegging 6 06-22-2010 06:09 PM
I want to build a kegerator RDLJr Bottling/Kegging 9 06-08-2009 05:21 PM
My Kegerator build up scotsmn30 Equipment/Sanitation 4 01-14-2008 02:47 AM
Kegerator - Buy New or Build? RoaringBrewer Bottling/Kegging 9 10-23-2007 07:10 PM