Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > DIY Projects > Help with HERMS in Keggle install
Reply
 
LinkBack Thread Tools
Old 03-23-2012, 04:18 AM   #1
akthor
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2010
Location: , ME
Posts: 1,463
Liked 24 Times on 22 Posts

Default Help with HERMS in Keggle install

Well I hope to be installing my 50' 1/2" HERMS coil into my HLT (keggle this weekend. In looking at it it appears it is going to be a royal PITA especially the bottom fitting getting this thing in there. Especially when you have big ham hands and sausage fingers.

Any tips, tricks or ideas on how to go about this? You can see by the pics I don't have a lot of room to maneuver.

2012-03-22-14.37.30.jpg   2012-03-22-14.37.42.jpg   2012-03-22-14.38.02.jpg  
__________________
TEN GALLON ALES
akthor is offline
 
Reply With Quote Quick reply to this message
Old 05-02-2012, 12:32 AM   #2
DeadBrew
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
DeadBrew's Avatar
Recipes 
 
Join Date: Dec 2011
Location: Canton, GA
Posts: 52
Liked 3 Times on 3 Posts

Default

Did you get this setup. I am looking to do the same thing in my hlt build and any info would help.

__________________
DeadBrew is offline
 
Reply With Quote Quick reply to this message
Old 05-02-2012, 02:01 AM   #3
psbuckland
Feedback Score: 2 reviews
Recipes 
 
Join Date: Feb 2011
Location: Frederick, MD
Posts: 189
Liked 3 Times on 3 Posts

Default

I don't see how it is going to possible with the stainless elbow/straight compression fitting combo. The angle is going to make it very difficult at best to align the coil in the compression fittings. One suggestion I would give is to get 1/2 NPT to 1/2 compression elbow fittings like this , insert the coil in the fittings before placing it in the kettle. Then just install the fitting as the inside of your weldless setup. Good luck on the install.


S-

__________________
psbuckland is offline
 
Reply With Quote Quick reply to this message
Old 05-02-2012, 06:53 AM   #4
akthor
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2010
Location: , ME
Posts: 1,463
Liked 24 Times on 22 Posts

Default

You are right it was too difficult due to the angle. I had to get two 90 degree compression fittings. Even with them if you have big ham hands like me it is not a fun time getting this thing installed. Doubly glad I went SS since I never want to have to remove the damn thing,

Quote:
Originally Posted by psbuckland View Post
I don't see how it is going to possible with the stainless elbow/straight compression fitting combo. The angle is going to make it very difficult at best to align the coil in the compression fittings. One suggestion I would give is to get 1/2 NPT to 1/2 compression elbow fittings like this , insert the coil in the fittings before placing it in the kettle. Then just install the fitting as the inside of your weldless setup. Good luck on the install.


S-
__________________
TEN GALLON ALES
akthor is offline
 
Reply With Quote Quick reply to this message
Old 05-02-2012, 02:29 PM   #5
KevinP
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2008
Location: Elk Grove Ca.
Posts: 94
Likes Given: 2

Default

May I ask where did you get the stainless tubing?

__________________
KevinP is offline
 
Reply With Quote Quick reply to this message
Old 05-02-2012, 02:54 PM   #6
jtkratzer
Senior Member
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
jtkratzer's Avatar
Recipes 
 
Join Date: Oct 2010
Location: Lititz, Pennsylvania
Posts: 2,805
Liked 38 Times on 38 Posts
Likes Given: 4

Default

I decided to make the diameter of my coil smaller for this reason using a corny keg, but I still think it's going to be a challenge as I'm using welded full couplings, so I have to thread the elbows into the couplings first, then get the compression fitting tightened down. I think I'll get the bottom part of the coil entirely mounted and tightened down and then work the top fitting and cut excess copper off if necessary.

The fittings I got from Bobby have the metal ferrules to make the fitting permenant or I can use o-rings to be able to break it down completely. Any reason to not make this permanent since the ferrules and o-rings are both readily available should I decide to do stainless some day?

jtkratzer is offline
 
Reply With Quote Quick reply to this message
Old 05-03-2012, 03:21 AM   #7
akthor
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2010
Location: , ME
Posts: 1,463
Liked 24 Times on 22 Posts

Default

Ebay, then HBT member Texan coiled it for me for a small fee.

UOTE=KevinP;4049604]May I ask where did you get the stainless tubing?[/QUOTE]

__________________
TEN GALLON ALES
akthor is offline
 
Reply With Quote Quick reply to this message
Old 05-03-2012, 04:14 AM   #8
StainlessBrewing
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2009
Location: Gilbert, AZ
Posts: 843
Liked 80 Times on 68 Posts
Likes Given: 135

Default

Just an FYI, we have it all in one place.

__________________
StainlessBrewing is offline
 
Reply With Quote Quick reply to this message
Old 05-03-2012, 03:18 PM   #9
audger
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: ., Connecticut
Posts: 1,497
Liked 40 Times on 40 Posts
Likes Given: 1

Default

it would be much easier if the coil wasnt unnecessarily long. the same functionality would be had with a 10-20 foot legnth.

__________________
audger is offline
 
Reply With Quote Quick reply to this message
Old 05-04-2012, 02:32 AM   #10
akthor
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2010
Location: , ME
Posts: 1,463
Liked 24 Times on 22 Posts

Default

Well I am using it as a HERMS and also after the boil to fill the HLT with ice and water and pump the wort back thru the coil for cooling.

I figure 50' was better than 25'?

It was a PITA to install but it's in. Someone with smaller arms and hands would probably have an easier time of it
lol

Quote:
Originally Posted by audger View Post
it would be much easier if the coil wasnt unnecessarily long. the same functionality would be had with a 10-20 foot legnth.
__________________
TEN GALLON ALES
akthor is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
SS HERMS permanent install problem. l3asturd DIY Projects 4 02-18-2012 03:01 PM
HERMS coil in Keggle jcalisi DIY Projects 6 03-08-2011 03:23 AM
Keggle Build: Where to Install Ball Valve? ultravista DIY Projects 7 01-25-2011 06:10 PM
SQ14 Burner - Keggle Ball Valve Install - Bargain Fittings jakecpunut DIY Projects 15 07-29-2010 12:16 PM
Keggle Valve Install Will319 DIY Projects 16 03-08-2010 03:29 PM