Happy HolidaySs Giveaway - Last Sponsor Giveaway of the Year!

Come Enter the BrewDeals/FastFerment Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Grain Mill Motor
 
 
LinkBack Thread Tools
Old 03-10-2012, 04:20 AM   #1
BubberJ
Junior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2009
Location: Metuchen, New Jersey
Posts: 22
Default Grain Mill Motor

I just found a "Brand New" Single-Phase AC Motor in the basement from my Father-in-law , honestly it has never been used but it from the 70's. The manufacture is Daytona. I wired it up and it runs fine but I have two questions before I by a pully for it and my grain mill shaft (belt too):

First: Single phase is not the strongest of the AC Motor group , Is it strong enough based off of your experiences?

Second: Can you put a variable control on the electric feed to maintain desire RPM's?

and since its Friday night I am enjoying a Sx Points Resin Prost!

Some Edits/Updates:

Its Dayton not Daytona
1/3 HP 1725 RPM 115V 5.4 AMP 60 Mz

__________________
BubberJ is offline
 
Quick reply to this message
Old 03-10-2012, 05:00 AM   #2
bigjason6
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Posts: 49
Liked 1 Times on 1 Posts

Default

That motor will be plenty strong enough to drive your grain mill.

Unless it specifically says it's a variable speed motor, don't try putting a speed control on it. A couple of pulleys will work just fine. Have fun!

__________________
bigjason6 is offline
 
Quick reply to this message
Old 03-10-2012, 05:07 AM   #3
BubberJ
Junior Member
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2009
Location: Metuchen, New Jersey
Posts: 22
Default

Thanks. Do you have a pulley size recommendation to keep the rpms in check of do you think I am fine with two 3" pulley's?

__________________
BubberJ is offline
 
Quick reply to this message
Old 03-10-2012, 05:21 AM   #4
bigjason6
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Posts: 49
Liked 1 Times on 1 Posts

Default

Not a problem! I haven't built anything like this yet. What I'd do is really slow down the RPMs on the mill by using a larger pulley on the mill shaft. 1750 RPMs seems way too fast in my opinion.

__________________
bigjason6 is offline
 
Quick reply to this message
Old 03-10-2012, 05:22 AM   #5
l3asturd
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
l3asturd's Avatar
Recipes 
 
Join Date: Dec 2011
Location: Visalia, CA
Posts: 464
Liked 8 Times on 7 Posts
Likes Given: 2

Default

Seems like you'd need to drop 1:10 ratio to get aroudn 172 RPM. Let me know what you end up doing, I have several of these same exact motors in my garage I've been trying to get rid of on ebay.

__________________
l3asturd is offline
 
Quick reply to this message
Old 03-10-2012, 02:46 PM   #6
purplehaze
HBT_SUPPORTER.png
Feedback Score: 2 reviews
 
purplehaze's Avatar
Recipes 
 
Join Date: Mar 2011
Location: , Massachusetts
Posts: 326
Liked 13 Times on 13 Posts
Likes Given: 4

Default pulley

You will need a 1" pulley on the motor shaft and a 10" pulley on the mill for a 10:1 ratio.

(Motor pulley diameter * motor RPM)/ Mill pulley diameter

The more critical of the two pulleys is the motor one. If your motor shaft is 1/2" in diameter you should have no trouble finding the correct pulley.
purplehaze is offline
 
Quick reply to this message
Old 03-10-2012, 03:39 PM   #7
yjfun
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jun 2010
Location: Arlington, Washington
Posts: 225
Liked 2 Times on 2 Posts

Default

You also need to take into account which belt you are using. Some of them don't like to make the turn around a very small pulley's diameter and they end up wearing out quickly or throwing themselves off a lot. I would think anything under 400 rpm would be good on the mill but closer to 200 is definitely better. You might want to consider no smaller than a 2 inch pulley on the motor and go from there.

__________________
yjfun is offline
 
Quick reply to this message
Old 03-10-2012, 04:20 PM   #8
RiverCityBrewer
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Location: Cincinnati, OH
Posts: 767
Liked 26 Times on 23 Posts
Likes Given: 2

Default

I had to use a 2" on mine... when I used a 1" sometimes the sheave would slip under load... moving to the larger sheave gave more surface area for the belt to grip... no problems since then.

__________________
RiverCityBrewer is offline
 
Quick reply to this message
Old 03-10-2012, 05:24 PM   #9
wrench
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2011
Location: Berlin, MA
Posts: 187
Liked 7 Times on 7 Posts
Likes Given: 2

Default

I agree with too small on the motor end causing problems. The problem with a bigger motor pulley, though, is that you need to go bigger on the other end as well. Those big 12" boys get expensive. Just be patient and do your homework to find a good price. I think I went with 1.5" and 12" on mine and it works great.

__________________
wrench is offline
 
Quick reply to this message
Old 03-10-2012, 07:49 PM   #10
l3asturd
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
l3asturd's Avatar
Recipes 
 
Join Date: Dec 2011
Location: Visalia, CA
Posts: 464
Liked 8 Times on 7 Posts
Likes Given: 2

Default

I have some super powerul 6RPM motors I was think of using, they're more useful for rotisseries but I thought about tasking one for grain or maybe making a mash stir. I have several of the 1200-1700 dayton motors so if they can be used I may just do that instead. I thought because they were so high RPM they wouldn't have the torque required.

__________________
l3asturd is offline
 
Quick reply to this message
 



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
grain mill motor bengerman DIY Projects 46 06-05-2012 12:14 AM
Grain mill motor size SpaceCoastBrew Other 1 12-22-2011 09:22 PM
Motor Salvage for Grain Mill horseinmay Other 22 11-21-2011 12:38 PM
Motor good for grain mill? Mose Other 11 03-25-2010 06:33 PM
Motor for Grain Mill Sawdustguy Other 43 10-26-2009 02:41 PM



Newest Threads

LATEST SPONSOR DEALS