Electric Brewing Supply 30A BCS Giveaway!


Home Brew Forums > Home Brewing Beer > DIY Projects > Gas question
Reply
 
LinkBack Thread Tools
Old 10-25-2012, 01:52 PM   #1
dbeer22
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Posts: 45
Liked 3 Times on 2 Posts

Default Gas question

I am building a single tier brewstand using 3 bg14 banjo burners. Do I need a regulator for each burner? If not how will the heat be affected when I am heating my HLT and mash run at the same time.

__________________
dbeer22 is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 02:35 PM   #2
MooMooBrew
HBT_SUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Apr 2011
Location: Willow Glen, CA
Posts: 174
Likes Given: 1

Default

Put needle valves between your manifold and your burners. Pump your manifold at fill blast from the tank/source, adjust flame from the needle valve.

__________________
MooMooBrew is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 03:12 PM   #3
dbeer22
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Posts: 45
Liked 3 Times on 2 Posts

Default

Would a gas ball valve work or does it have to be a needle valve?

__________________
dbeer22 is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 04:35 PM   #4
josterhues
Jace Brewing
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
josterhues's Avatar
Recipes 
 
Join Date: Aug 2012
Location: Lebanon, Cincinnati, Ohio
Posts: 134
Liked 7 Times on 5 Posts

Default

I just got done with my stand single teir with the bg14s and I used an adjustable regulator from amazon and gas balls valves from home depot and it runs great. The regulator to me was most important because once I got it adjusted right the burners looked great.

Here is a pic with them all going. The middle burner is a smaller banjo burner.

forumrunner_20121025_123507.jpg

__________________
josterhues is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 04:53 PM   #5
tally350z
HBT_SUPPORTER.png
Feedback Score: 4 reviews
 
tally350z's Avatar
Recipes 
 
Join Date: May 2011
Location: Tallahassee, FL
Posts: 1,188
Liked 79 Times on 67 Posts
Likes Given: 1

Default

I use gas ball valves rather than needle valves and I can control the flame on mine with no issues. Although when you adjust its a subtle turn, my burners run great.

__________________
Toasting Tortoise Brewery
Primary - Smoked Belgium
Secondary - SOUR TORTOISE
Kegged
- Burton IPA, Munich Lager, Cream Ale
Bottled - Muscadine Port, Imperial Stout

North Florida Brewers League
tally350z is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 05:53 PM   #6
dbeer22
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Posts: 45
Liked 3 Times on 2 Posts

Default

Do you guys use heat shields? How far do you set the burners from the kettle?

__________________
dbeer22 is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 07:59 PM   #7
tally350z
HBT_SUPPORTER.png
Feedback Score: 4 reviews
 
tally350z's Avatar
Recipes 
 
Join Date: May 2011
Location: Tallahassee, FL
Posts: 1,188
Liked 79 Times on 67 Posts
Likes Given: 1

Default

Mine are about 4 inches from the bottom of the keggle. I have three pieces of steel around the burner for the heat shield. I put a fourth one but it was starving the burner.

__________________
Toasting Tortoise Brewery
Primary - Smoked Belgium
Secondary - SOUR TORTOISE
Kegged
- Burton IPA, Munich Lager, Cream Ale
Bottled - Muscadine Port, Imperial Stout

North Florida Brewers League
tally350z is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 09:03 PM   #8
josterhues
Jace Brewing
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
josterhues's Avatar
Recipes 
 
Join Date: Aug 2012
Location: Lebanon, Cincinnati, Ohio
Posts: 134
Liked 7 Times on 5 Posts

Default

Do you plan on using low pressure or high pressure? I used heat shields because it made mounting my burners easier.

__________________
josterhues is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 09:18 PM   #9
dbeer22
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jul 2012
Posts: 45
Liked 3 Times on 2 Posts

Default

I plan on getting a 0-30psi high pressure regulator. I have the burners mounted already without heat shields, I can add them just not sure if I need to

__________________
dbeer22 is offline
 
Reply With Quote Quick reply to this message
Old 10-25-2012, 10:12 PM   #10
josterhues
Jace Brewing
HBT_SUPPORTER.png
Feedback Score: 1 reviews
 
josterhues's Avatar
Recipes 
 
Join Date: Aug 2012
Location: Lebanon, Cincinnati, Ohio
Posts: 134
Liked 7 Times on 5 Posts

Default

Do you have welded or weldless fittings? When I was using mine the front got really hot even with shields.

Do you have a pic of your build so far?

__________________
josterhues is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
European bottle capping question + yeast starter question Rev2010 Beginners Beer Brewing Forum 12 12-01-2013 03:37 AM
Stock pot question and general nrmew brewer question Charliehart1 Beginners Beer Brewing Forum 8 04-19-2011 03:33 PM
Idopher question and basic yeast washing question msa8967 Beginners Beer Brewing Forum 2 02-12-2011 04:21 PM
Quick temprate question, and promary/secondary question. Cazamodo Fermentation & Yeast 4 10-23-2010 08:52 PM
Making Chocolate Oatmeal stout. OG question and smack pack starter Question. britishbloke Beginners Beer Brewing Forum 10 02-23-2007 05:01 PM