New Giveaway - Wort Monster Conical Fermenter!

Home Brew Forums > Home Brewing Beer > DIY Projects > Electric Heating Element




Reply
 
LinkBack Thread Tools Display Modes
Old 04-24-2010, 07:10 PM   #1
noblanks1969
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2009
Location: Fairborn, Ohio
Posts: 16
Default Electric Heating Element

I'm using a 5500wt extra low density element and the very end of the element, which is bent back over itself, is too long and still inside the fitting being used. The problem is that the element is touching the side of the SS fitting, which will most likely cause too much heat transfer into the metal. Can I use copper wire to tie or clamp the loose end of the element to itself, allowing space between the fitting and element; preventing direct contact? Would this pose any safety or functional issues as the element will be in contact with itself? Thank you, Ron



__________________
noblanks1969 is offline
 
Reply With Quote Quick reply to this message
Old 04-24-2010, 11:34 PM   #2
P-J
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2010
Location: Charlotte, NC
Posts: 3,154
Liked 234 Times on 188 Posts
Likes Given: 398

Default

What fitting are you using? Where are you installing the element (kettle, cooler)?

I would not do as you suggested. There is another solution.



__________________
P-J is offline
 
Reply With Quote Quick reply to this message
Old 04-25-2010, 02:53 AM   #3
Brewmoor
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Brewmoor's Avatar
Recipes 
 
Join Date: Aug 2009
Location: Colorado
Posts: 1,094
Liked 12 Times on 12 Posts
Likes Given: 13

Default

Why worry about the heat transfer to the coupler? If it indeed transfers heat to the metal then the liquid touching that metal should heat as well.

Maybe I am not following what you are explaining.

__________________

"What the mind can conceive and believe, the mind can achieve."

My build thread. Compact Single Tier!

Brewmoor is offline
 
Reply With Quote Quick reply to this message
Old 04-25-2010, 04:17 AM   #4
CodeRage
Death by Magumba!
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
CodeRage's Avatar
Recipes 
 
Join Date: Aug 2007
Location: Melbourne, Fl
Posts: 2,254
Liked 29 Times on 16 Posts
Likes Given: 5

Default

The element is attached to the metal bulkhead you thread into the coupler. No over heating issue there right? same goes with the pot or anything else for that matter. As long as the element is submerged than you are all good.

__________________
Brutus 20e build | Electrical Primer for Brewers | Auber SYL-2362A2 PID Install & Config
So as I am walking out the door this morning I think to my self:
"self, going to work on Monday is like knowing you're going to get kicked in the nuts. You just don't know when or by who"
CodeRage is offline
 
Reply With Quote Quick reply to this message
Old 04-25-2010, 10:45 AM   #5
wilserbrewer
Vendor
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 7 reviews
 
wilserbrewer's Avatar
Recipes 
 
Join Date: May 2007
Location: Jersey Shore, Jersey
Posts: 6,202
Liked 331 Times on 284 Posts
Likes Given: 7

Default

Quote:
Originally Posted by MslmKllr View Post
Can I use copper wire to tie or clamp the loose end of the element to itself, allowing space between the fitting and element; preventing direct contact? Would this pose any safety or functional issues as the element will be in contact with itself? Thank you, Ron
Not a problem, the outside of the element is not energized, it can touch itself, the pot, or a fitting, or ground. Securing it w/ a copper wire tie shouldn't pose a problem IMO.

Disclaimer...I am a jack of all trades...master of none and consider electric to be one of my weaker skills. Hopefully an expert will concur...
__________________
wilserbrewer
BIAB Bags, Hop Bags and Ratchet Pulleys for sale

Expert tailor and supplier of custom sized, top quality BIAB bags, hop bags and ratchet pulleys at reasonable pricing

http://biabbags.webs.com/


CORONA MILL BUCKET SYSTEM V. 2.0
wilserbrewer is offline
 
Reply With Quote Quick reply to this message
Old 04-25-2010, 03:57 PM   #6
noblanks1969
Feedback Score: 0 reviews
Recipes 
 
Join Date: Oct 2009
Location: Fairborn, Ohio
Posts: 16
Default

Thanks...the kettle goes to the welder in the morning. I'll let you all know how it works out. Ron



__________________
noblanks1969 is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
electric heating element Brewpastor DIY Projects 9 01-01-2012 09:20 PM
Going electric, heating element question. jmp138 DIY Projects 33 02-27-2011 12:16 AM
Electric heating element CircleC-Brewer Equipment/Sanitation 4 08-04-2008 08:26 PM
No-welding electric heating element? RockfordWhite DIY Projects 4 12-27-2007 05:52 AM
Electric heating element requirements FrankC Equipment/Sanitation 7 01-02-2007 10:59 PM