Ss Brewing Technologies Giveaway!

Home Brew Forums > Home Brewing Beer > DIY Projects > e-keggle in keg with plastic coating on top
Reply
 
LinkBack Thread Tools
Old 02-09-2012, 04:28 PM   #1
jimwright
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2006
Posts: 9
Default e-keggle in keg with plastic coating on top

Hey Folks,
Looking to do an e-keggle project, maybe I'm overthinking it but I'm just wondering if I should try to cut the plastic coating off the top of this keg before marking and cutting the top hole or if I should just mark on the plastic and cut through it all.

I'm planning on using a dremel, should I just use that carefully to take the plastic off first?

Also this looks a bit different that most of the kegs I see on here, it says it's 13.2 gallon instead of 15 any inherent problems with using it for a kettle?




Thanks, I don't post much but I'd be lost in the brewing world without this forum.

__________________
jimwright is offline
 
Reply With Quote Quick reply to this message
Old 02-09-2012, 05:07 PM   #2
conpewter
HBT_SUPPORTER.png
Feedback Score: 0 reviews
 
conpewter's Avatar
Recipes 
 
Join Date: Nov 2007
Location: East Dundee, Illinois
Posts: 5,109
Liked 41 Times on 36 Posts
Likes Given: 7

Default

Well if you cut all the plastic off the top you won't have the handles, but that may not matter to you (I still have needed to move my keggle with 5 gal in it on occasion). I think it could work. I'd use a sharp razorblade to cut the plastic back, then cut the metal with your dermel or grinder, but stay back 1/4" from the rubber.

__________________

"People should not be afraid of their governments. Governments should be afraid of their people." - V

Primary: Nothin
Secondary: Shady Lord RIS, Water to Barleywine, Pumpkin wine, burnt mead
Kegged: Crappy infected mild
Bottles: Apfelwein, 999 Barleywine, Oatmeal Stout, Robust Porter, Robust smoked porter, Simcoe Smash

conpewter is offline
 
Reply With Quote Quick reply to this message
Old 02-09-2012, 05:25 PM   #3
jimwright
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2006
Posts: 9
Default

oh so the handles are entirely plastic? i thought everything was metal just with a thin plastic coating... interesting. i'll try using an exacto knife or razor blade to cut off a big circle of plastic on the top.

cheers.

__________________
jimwright is offline
 
Reply With Quote Quick reply to this message
Old 02-09-2012, 08:30 PM   #4
jimwright
Feedback Score: 0 reviews
Recipes 
 
Join Date: Aug 2006
Posts: 9
Default

Took a quick sample cut out of the top. I guess I may be going through more dremel blades than I thought, this plastic is a good half-inch thick. I think the earlier idea of just cutting the circle out of the plastic and then cutting the steel a quarter inch in or so is the best idea. An angle grinder would probably be best for this but unfortunately I don't own one and it would probably kick up way more dust and sparks than I'd like in an apartment environment. Is there a particular dremel disk that would be best for cutting plastic? I've just been using the fiberglass reinforced ones so far. Or maybe a better tool in general for the job?

Sorry for the crap quality photo, my phone doesn't take the best lowlight pics.

__________________
jimwright is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Powder Coating caskconditioned DIY Projects 6 03-28-2011 04:15 PM
Waynes coating Metsbrew DIY Projects 5 01-03-2011 03:38 PM
How to Remove galvanized coating from kegs. Grimm DIY Projects 12 08-05-2010 11:41 AM
powder coating jcalisi DIY Projects 5 03-24-2009 01:56 PM
plastic shank vmpolesov DIY Projects 1 01-22-2008 06:27 AM