New Giveaway - Wort Monster Conical Fermenter!

Home Brew Forums > Home Brewing Beer > DIY Projects > Bulk Extract Container as fermenter




Reply
 
LinkBack Thread Tools Display Modes
Old 05-31-2012, 06:41 PM   #1
texasbrewer73
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: The Colony, Texas
Posts: 144
Liked 8 Times on 6 Posts
Likes Given: 1

Default Bulk Extract Container as fermenter

So I got one of those 15gal (estimated) containers from my LHBS to ferment in for $5. It's been a cheap way to ferment 10 gal batches, but I'm tired of siphoning into a secondary. I'd like to put one of those cheap plastic valves on it that are used on bottling buckets, but not sure how to mount it flush without losing beer. There's no threads on the bulkhead to add a diptube. I'm curious to see if this is done or ideas the community may have. I only need to pull about an inch or so of beer before I fear disturbing the trub.

fermenter1.jpg

fermenter2.jpg



__________________
texasbrewer73 is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 08:33 PM   #2
shroomzofdoom
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Location: Piscataway, NJ
Posts: 609
Liked 9 Times on 9 Posts
Likes Given: 6

Default

My long autosiphon just about reaches the bottom of the 15g extract barrel i got-but it has to go down inside of the opening a few inches. I start the autosiphon and drain about the top few gallons, then hang it it a bit by the hose to go all the way. You can also get a long length of racking cane or SS tubing as well (no autosiphon) to do the job.

If I were going to put a valve on the bottom, I'd steer clear of the bottling spigots. I think these would give you problems. I'd go more with a SS ball valve/bulkhead weldleas setup.

Hope that helps.



__________________
Mike D

My electric BCS-460 build (work in progress)

Coffin cooling lessons
shroomzofdoom is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 08:47 PM   #3
tre9er
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Lincoln, NE
Posts: 4,338
Liked 230 Times on 195 Posts
Likes Given: 35

Default

Use a drilled rubber stopper and a bent piece of copper or racking cane as a diptube in the bottling spigot. Revvy has a thread on this. I believe it's a bottling tutorial.

But I agree I'd spend the $27 shipped or so to get a keg/kettle weldless bulkhead. I have 2 of them on kettles and they don't leak. Have the cooler bulkhead on my MLT and it's great, too. BargainFittings.com

__________________

_________________________________
Skal!
Den Faaborg Bryggeri

Quote:
Originally Posted by davekippen View Post
Open log Fermenting and gas-can secondary?? I am planning my next brew right now!!
tre9er is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 09:25 PM   #4
texasbrewer73
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: The Colony, Texas
Posts: 144
Liked 8 Times on 6 Posts
Likes Given: 1

Default

Thanks for the input. I've at least got something to go on now.

Given that there is no real opening at the top to get my hands/arm into, not sure which method I'll go with. Getting the plastic spigot in wouldn't be much of a problem with the string/tube method. The stopper and a tube might be a little more difficult. I am going to move to a DIY conical eventually, so the SS ball valve would at least get repurposed.

__________________
texasbrewer73 is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 09:40 PM   #5
tre9er
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2012
Location: Lincoln, NE
Posts: 4,338
Liked 230 Times on 195 Posts
Likes Given: 35

Default

FWIW, I autosiphon from my ale pails, all four of them. I don't love it (especially cause my siphon doesn't have a clip) but I haven't gotten fed-up enough to change the procedure. You are not alone, my friend.

__________________

_________________________________
Skal!
Den Faaborg Bryggeri

Quote:
Originally Posted by davekippen View Post
Open log Fermenting and gas-can secondary?? I am planning my next brew right now!!
tre9er is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 11:06 PM   #6
shroomzofdoom
Feedback Score: 0 reviews
Recipes 
 
Join Date: Dec 2009
Location: Piscataway, NJ
Posts: 609
Liked 9 Times on 9 Posts
Likes Given: 6

Default

I think I get the problem now duh.... The openings are too small? I don't think you'll be able to get a tool or arm down inside for the nut/bulkhead fitting.

__________________
Mike D

My electric BCS-460 build (work in progress)

Coffin cooling lessons
shroomzofdoom is offline
 
Reply With Quote Quick reply to this message
Old 05-31-2012, 11:40 PM   #7
texasbrewer73
Feedback Score: 0 reviews
Recipes 
 
Join Date: Mar 2012
Location: The Colony, Texas
Posts: 144
Liked 8 Times on 6 Posts
Likes Given: 1

Default

You can tie a string to a washer or something, then run the string through the nut inside the fermenter and then through the spigot on the outside. Pull the string to put pressure on the nut, then turn the spigot to tighten. Same concept with a SS valve. I saw a thread were a guy did that with a 60 gal conical that he couldn't reach into. Gave me the idea to do that in this thing with its 2" opening. I don't know. I may just say to hell with it and build the conical.



__________________
texasbrewer73 is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
Ever use a shipping container for brew shed?? Jester DIY Projects 24 12-14-2011 01:10 PM
20/40ft Storage container- portable nanobrewery? lewissimonj DIY Projects 8 01-10-2011 09:33 PM
Mash Tun from old LME container? RegionalChaos DIY Projects 5 04-28-2010 05:09 PM
Single container RIMS - possible? Listende-elg DIY Projects 12 11-14-2009 01:14 AM
Who Needs A Pet Food Container? Brewsmith DIY Projects 12 04-30-2008 02:39 AM